LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsDigital electricity meters blink an LED for every unit of energy, typically 3,200 times per kWh. An LDR taped over the LED counts the flashes; the time between two flashes gives the power right now and the total gives kWh used. Switch appliances on one by one to see what each costs to run.
Never open the meter or touch its terminals. The sensor sits on the outside of the glass only.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
energy_meter_pulse_reader.inoVerify & upload in Electrolark// Electricity meter pulse reader
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "energy-meter-pulse-reader"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t LDR_PIN = 2;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
bool dark = false;
const float IMP_PER_KWH = 3200; // printed on your meter, e.g. "3200 imp/kWh"
volatile unsigned long pulses = 0;
unsigned long lastPulseAt = 0, prevPulseAt = 0;
bool wasLit = false;
unsigned long lastShow = 0;
void setup() {
Serial.begin(115200);
pinMode(LDR_PIN, INPUT);
lcd.init();
lcd.backlight();
}
void loop() {
bool lit = digitalRead(LDR_PIN) == LOW; // the LDR module output goes LOW when the meter LED flashes
if (lit && !wasLit) { pulses++; prevPulseAt = lastPulseAt; lastPulseAt = millis(); }
wasLit = lit;
if (millis() - lastShow > 1000) {
lastShow = millis();
float kwh = pulses / IMP_PER_KWH;
float watts = 0;
if (prevPulseAt && millis() - lastPulseAt < 120000UL) // power from the gap between the last two flashes
watts = 3600000.0f / IMP_PER_KWH / ((lastPulseAt - prevPulseAt) / 1000.0f);
lcd.setCursor(0, 0); lcd.print(F("Now ")); lcd.print(watts, 0); lcd.print(F(" W "));
lcd.setCursor(0, 1); lcd.print(F("Used ")); lcd.print(kwh, 3); lcd.print(F(" kWh "));
Serial.print(watts, 0); Serial.print(F(" W, ")); Serial.print(kwh, 3); Serial.println(F(" kWh"));
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Some modules invert DO. Change == HIGH to == LOW in the code.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Digital LDR Light Sensor Module – LM393, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (energy_meter_pulse_reader.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹462 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Thresholds set in hardware vs software.
Never open the meter or touch its terminals. The sensor sits on the outside of the glass only.
Ideas that reuse this build: Inverter battery monitor and Power-cut alarm. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0 W, 0.000 kWh 0 W, 0.000 kWh
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.