LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsSeedlings on a windowsill stretch and flop in winter because the day is too short. Between 6:00 and 20:00 this controller checks the light sensor and runs a 12 V grow strip whenever the room is dark, so the plants get a full day without wasting electricity at noon.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
grow_light_timer.inoVerify & upload in Electrolark// Grow light that tops up daylight
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "grow-light-timer"
#include <Wire.h>
#include <RTClib.h>
// ---- pins ----
const uint8_t LDR_PIN = 2;
const uint8_t RELAY_PIN = 3;
RTC_DS3231 rtc;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
bool dark = false;
const int DAY_START_H = 6, DAY_END_H = 20; // plants get light between these hours, but only when the room is dark
unsigned long lastShow = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
pinMode(LDR_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
DateTime now = rtc.now();
dark = digitalRead(LDR_PIN) == HIGH;
bool daytime = now.hour() >= DAY_START_H && now.hour() < DAY_END_H;
bool on = daytime && dark;
setRelay(on);
if (millis() - lastShow > 5000) {
lastShow = millis();
Serial.print(now.hour()); Serial.print(':'); Serial.print(now.minute()); Serial.print(dark ? F(" room dark ") : F(" room bright ")); Serial.println(on ? F("lamp ON") : F("lamp off"));
}
delay(500);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Some modules invert DO. Change == HIGH to == LOW in the code.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
7 parts: Nano CH340 Development Board (Soldered), DS3231 Precision RTC Module with EEPROM, Digital LDR Light Sensor Module – LM393, 5V Relay Module with Optocoupler (1 channel), Enclosed SMPS Power Supply (12V), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (grow_light_timer.ino). Install this library first: RTClib.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹739 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Isolation, relays and switching higher-power loads; Real-time clocks and backup batteries; Thresholds set in hardware vs software.
Ideas that reuse this build: Automatic watering and Night light. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.