Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsHumidity above 60 % feels sticky and above 75 % lets mould grow on walls, clothes and books. The ring lights up with the humidity: green up to 60 %, amber to 75 %, red above that. Place it in a bedroom, bathroom or cupboard to know when to run a dehumidifier or open the windows.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
humidity_comfort_ring.inoVerify & upload in Electrolark// Humidity comfort colour ring
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "humidity-comfort-ring"
#include <DHT.h>
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t RING_PIN = 3;
DHT dht(DHT_PIN, DHT22);
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
uint32_t bandColor(int pct) {
if (pct < 60) return ring.Color(0, 160, 60); // green
if (pct < 75) return ring.Color(200, 120, 0); // amber
return ring.Color(220, 0, 0); // red
}
void setup() {
Serial.begin(115200);
dht.begin();
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
int pct = constrain((int)(humidity), 0, 100);
showLevel(pct, bandColor(pct));
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), DHT22 Temperature & Humidity Sensor, WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (humidity_comfort_ring.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor and Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹463 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Wardrobe monsoon dehumidifier and Humidity servo dial. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=26.9C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.