Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe servo does not jump to its new angle; the sketch moves it one degree at a time, so a curtain or lid opens smoothly. The same idea works for a vent flap or a hamster-cage door with a larger servo.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
38 kHz infrared receiver that decodes button codes from almost any TV or AC remote.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
ir_remote_servo_door_model.inoVerify & upload in Electrolark// IR remote servo door or curtain model
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "ir-remote-servo-door-model"
#include <IRremote.hpp>
#include <Servo.h>
// ---- pins ----
const uint8_t IR_PIN = 2;
const uint8_t SERVO_PIN = 3;
Servo servo;
// Put your remote's number-key codes here (find them with the IR code reader project)
const uint16_t CMD_1 = 0x0C, CMD_2 = 0x18, CMD_3 = 0x5E;
const int ANGLE_1 = 0, ANGLE_2 = 90, ANGLE_3 = 180; // closed, half open, fully open
int current = 0;
void setup() {
Serial.begin(115200);
IrReceiver.begin(IR_PIN);
servo.attach(SERVO_PIN);
servo.write(ANGLE_1); current = ANGLE_1;
}
void loop() {
if (IrReceiver.decode()) {
uint16_t cmd = IrReceiver.decodedIRData.command;
IrReceiver.resume();
int target = -1;
if (cmd == CMD_1) target = ANGLE_1; else if (cmd == CMD_2) target = ANGLE_2; else if (cmd == CMD_3) target = ANGLE_3;
if (target < 0) { Serial.print(F("Unused command 0x")); Serial.println(cmd, HEX); return; }
int step = target > current ? 1 : -1;
while (current != target) { current += step; servo.write(current); delay(12); } // glide slowly to the new angle
Serial.print(F("Angle ")); Serial.println(current);
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Point the remote straight at the receiver, check the OUT pin, and try a fresh remote battery.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Digital 38kHz Infrared Receiver Module, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (ir_remote_servo_door_model.ino). Install these libraries first: IRremote and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹468 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Infrared remote protocols (NEC); PWM pulses and servo control.
Ideas that reuse this build: IR remote relay switch and IR code reader. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.