Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe accelerometer on a pump or mill housing drives the ring: green under 0.3 g, amber to 0.6 g and red above. A mechanic can see the health of the machine from across the shop without reading a number.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three-axis accelerometer that feels gravity and bumps, so it can measure tilt angles and detect knocks, drops and vibration.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
machine_shake_health_ring.inoVerify & upload in Electrolark// Machine shake health ring
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "machine-shake-health-ring"
#include <Wire.h>
#include <Adafruit_ADXL345_U.h>
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t RING_PIN = 2;
Adafruit_ADXL345_Unified accel = Adafruit_ADXL345_Unified(12345);
float adxX = 0, adxY = 0, adxZ = 1; // in g
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
void readAdxl() {
sensors_event_t e;
accel.getEvent(&e);
adxX = e.acceleration.x / 9.81f; adxY = e.acceleration.y / 9.81f; adxZ = e.acceleration.z / 9.81f;
}
float adxPitch() { return atan2(-adxX, sqrt(adxY * adxY + adxZ * adxZ)) * 57.3f; }
float adxRoll() { return atan2(adxY, adxZ) * 57.3f; }
float adxShake() { float m = sqrt(adxX * adxX + adxY * adxY + adxZ * adxZ); return fabs(m - 1.0f); }
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
uint32_t bandColor(int pct) {
if (pct < 30) return ring.Color(0, 160, 60); // green
if (pct < 60) return ring.Color(200, 120, 0); // amber
return ring.Color(220, 0, 0); // red
}
void setup() {
Serial.begin(115200);
if (!accel.begin()) Serial.println(F("ADXL345 not found"));
accel.setRange(ADXL345_RANGE_4_G);
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
pitchDeg = (readAdxl(), adxPitch());
rollDeg = adxRoll();
shakeG = adxShake();
int pct = constrain((int)(constrain((int)(shakeG * 100), 0, 100)), 0, 100);
showLevel(pct, bandColor(pct));
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Roll="));
Serial.print(rollDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.println();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x53 (0x1D if the ALT pin is high).
Keep the board still while it starts, and check pitch and roll are not swapped for your mounting.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), ADXL345 Digital Acceleration Sensor Module – I2C/SPI, 3.3V/5V, WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (machine_shake_health_ring.ino). Install these libraries first: Adafruit ADXL345 and Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹520 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, tilt angles and shock detection; Addressable LEDs and colour mixing.
Ideas that reuse this build: Washing machine spin shake alarm and Machine vibration colour ring. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g Pitch=0.0deg, Roll=0.0deg, Shake=0.00g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.