Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsStick a picture on each RFID card: a cow, a mango, the letter A. When a child taps a card, the Uno reads its ID and the DFPlayer plays the matching recording. Scan a new card and its ID appears in the Serial Monitor, ready to add to the table.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
13.56 MHz RFID/NFC reader that reads the unique ID of cards and key fobs held near it.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
rfid_talking_flashcards.inoVerify & upload in Electrolark// RFID talking flashcards for children
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "rfid-talking-flashcards"
#include <SPI.h>
#include <MFRC522.h>
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t RFID_SS = 2;
const uint8_t RFID_RST = 3;
const uint8_t MP3_RX = 4;
const uint8_t MP3_TX = 5;
MFRC522 rfid(RFID_SS, RFID_RST);
DFRobotDFPlayerMini player;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 22;
// card IDs and the track each one plays: scan a new card, copy its ID from the Serial Monitor into this table
struct Card { uint32_t id; uint8_t track; };
const Card CARDS[] = { {0x12345678, 1}, {0x9ABCDEF0, 2}, {0x0BADF00D, 3} };
const int NCARDS = sizeof(CARDS) / sizeof(CARDS[0]);
void setup() {
Serial.begin(115200);
SPI.begin();
rfid.PCD_Init();
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
}
void loop() {
if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) { delay(50); return; }
uint32_t id = 0;
for (byte i = 0; i < 4 && i < rfid.uid.size; i++) id = (id << 8) | rfid.uid.uidByte[i];
Serial.print(F("Card 0x")); Serial.println(id, HEX);
for (int i = 0; i < NCARDS; i++) if (CARDS[i].id == id) { player.playMp3Folder(CARDS[i].track); break; }
rfid.PICC_HaltA();
delay(800);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check it is on 3.3 V and the SPI wires (SCK, MOSI, MISO) are on the hardware SPI pins.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, RC522 RFID Reader / Writer SPI Module with Card & Tag, DFPlayer Mini MP3 Player Module (MP3-TF-16P), Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (rfid_talking_flashcards.ino). Install these libraries first: MFRC522 and DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,011 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
RFID, UIDs and SPI; Serial-controlled audio playback.
Ideas that reuse this build: RFID door lock and Exhibit audio guide. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.