Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsChilli, tomato and brinjal seeds sit for weeks in cold soil. A heating pad under the trays, a probe in the soil and a relay keep the root zone between 26 and 28 °C; the display shows the temperature. Seeds that took three weeks often come up in five to seven days.
Put the pad under a waterproof tray, never in water, and check the wiring stays dry when you water.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter feeds the heating pad through the relay (COM and NO). Use a pad of 20 W or less with this relay module, and fuse the 12 V line at 3 A.
seed_germination_heater.inoVerify & upload in Electrolark// Seed germination chamber heater
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "seed-germination-heater"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t RELAY_PIN = 3;
const uint8_t SEG_CLK = 4;
const uint8_t SEG_DIO = 5;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 26; // most vegetable seeds germinate fastest at 25-30 C
const float HYSTERESIS = 2; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
{ float segV = probeC; // shows 0.00 to 9.99, then 10.0 to 99.9, with a decimal point
if (segV < 0) seg.showNumberDec((int)round(segV), false);
else {
segV = min(segV, 99.9f);
int n = segV < 10 ? (int)round(segV * 100) : (int)round(segV * 10);
uint8_t s[4] = {seg.encodeDigit(n / 100 % 10), seg.encodeDigit(n / 10 % 10), seg.encodeDigit(n % 10), 0};
s[segV < 10 ? 0 : 1] |= 0x80; // decimal point
seg.setSegments(s);
}
}
}
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC < ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Heating" : "Warm";
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, 5V Relay Module with Optocoupler (1 channel), TM1637 4-Digit 7-Segment Display Module, Resistor Assortment Kit (30 Values), 12V Silicone Heating Pad (100 × 100mm), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (seed_germination_heater.ino). Install these libraries first: OneWire, DallasTemperature and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹913 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Isolation, relays and switching higher-power loads; Multiplexed 7-segment displays.
Ideas that reuse this build: Seedling tray dry alarm and Curd incubator. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, status=Warm Probe=26.0C, status=Warm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.