Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe microphone level drives a rainbow bar along 30 LEDs, with a white "peak" dot that falls slowly like a studio VU meter. Place it next to a speaker and turn the module gain until loud beats reach the top.
Tick anything you already have and the total updates.
Addressable RGB LED strip: cut to length (here 30 LEDs, half a metre) and control every LED individually from one data pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Power the strip from a separate 5 V 2 A supply; join its GND to the Nano GND.
sound_reactive_led_strip.inoVerify & upload in Electrolark// Music-reactive LED strip
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "sound-reactive-led-strip"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const uint8_t RING_PIN = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const int RING_LEDS = 30;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
int soundPct = 0;
float level = 0;
float peak = 0;
uint16_t hueBase = 0;
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void setup() {
Serial.begin(115200);
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
soundPct = readSoundLevel(); // 50 ms of sampling
level = level * 0.6f + soundPct * 0.4f;
if (level > peak) peak = level; else peak *= 0.97f;
int lit = constrain((int)(level * RING_LEDS / 60), 0, RING_LEDS);
int peakLed = constrain((int)(peak * RING_LEDS / 60), 0, RING_LEDS - 1);
for (int i = 0; i < RING_LEDS; i++) {
uint32_t c = 0;
if (i < lit) c = ring.gamma32(ring.ColorHSV(hueBase + i * 2000));
if (i == peakLed) c = ring.Color(255, 255, 255);
ring.setPixelColor(i, c);
}
ring.show();
hueBase += 150;
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), Analog Sound Sensor Microphone Module, WS2812B Addressable RGB LED Strip (60 LEDs/m), Resistor Assortment Kit (30 Values), Breadboard Power Supply Module (3.3V / 5V), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (sound_reactive_led_strip.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹936 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Sampling a waveform and measuring amplitude.
Ideas that reuse this build: Remote-controlled mood light and Classroom noise meter. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.