Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsMany home sounds carry information: the doorbell, the cooker whistle, a smoke alarm or a baby crying. Place the microphone near the sound you care about; when it gets loud, the ring flashes bright white and the vibration motor buzzes for 15 seconds. Put the ring where you usually sit, or run a long wire to the bedroom.
An aid, not a certified fire alarm. Use a proper smoke alarm with a strobe for fire safety.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
sound_to_light_alert_for_deaf.inoVerify & upload in Electrolark// Sound-to-light alert for deaf and hard-of-hearing users
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "sound-to-light-alert-for-deaf"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const uint8_t RING_PIN = 2;
const uint8_t VIBE_PIN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
int soundPct = 0;
const int LOUD_PCT = 55; // louder than this for a moment counts as a sound to report
const unsigned long FLASH_MS = 15000; // flash and buzz this long after the last loud sound
unsigned long lastLoud = 0;
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
ring.begin();
ring.setBrightness(40);
ring.show();
pinMode(VIBE_PIN, OUTPUT);
}
void loop() {
soundPct = readSoundLevel();
if (soundPct > LOUD_PCT) lastLoud = millis();
bool alert = lastLoud && millis() - lastLoud < FLASH_MS;
bool on = alert && (millis() / 300) % 2 == 0;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, on ? ring.Color(255, 255, 255) : 0); // bright white flash
ring.show();
setVibe(alert && (millis() / 600) % 2 == 0);
static unsigned long lastLog = 0;
if (millis() - lastLog > 500) { lastLog = millis(); Serial.print(F("Sound ")); Serial.print(soundPct); Serial.println(alert ? F(" % ALERT") : F(" %")); }
delay(20);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Check the transistor orientation (flat face: C-B-E for BC547).
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), Analog Sound Sensor Microphone Module, WS2812 RGB LED Ring (16 LEDs), Coin Vibration Motor 3V, Resistor Assortment Kit (30 Values), General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (sound_to_light_alert_for_deaf.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹529 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Sampling a waveform and measuring amplitude; Transistors as switches.
An aid, not a certified fire alarm. Use a proper smoke alarm with a strobe for fire safety.
Ideas that reuse this build: Silent vibration doorbell and Clap switch. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Sound 10 % Sound 9 % Sound 9 % Sound 9 %
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.