LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsSet-top boxes, speakers and chargers often draw power around the clock. With the INA219 in the DC lead, the OLED shows the milliwatts a device draws when it is on, in standby and when it is "off", so you know which ones are worth unplugging.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
Follow the colours: red is power, dark grey is ground, blue is a signal.
standby_power_finder.inoVerify & upload in Electrolark// Standby power finder for DC adapters
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "standby-power-finder"
#include <Wire.h>
#include <Adafruit_INA219.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_INA219 ina;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Standby"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Current: "));
oled.print(currentMa, 0);
oled.print(F(" mA"));
oled.setCursor(0, 24);
oled.print(F("Power: "));
oled.print(powerMw, 0);
oled.print(F(" mW"));
oled.display();
}
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
powerMw = ina.getPower_mW();
Serial.print(F("Current="));
Serial.print(currentMa, 0);
Serial.print(F("mA"));
Serial.print(F(", Power="));
Serial.print(powerMw, 0);
Serial.print(F("mW"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), INA219 Current and Power Monitor Module, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (standby_power_finder.ino). Install these libraries first: Adafruit INA219, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹668 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Shunt resistors, current and power.
Ideas that reuse this build: Electricity cost meter and DIY USB power meter. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Current=448mA, Power=5407mW Current=448mA, Power=5402mW Current=451mA, Power=5403mW Current=448mA, Power=5402mW Current=452mA, Power=5420mW
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.