Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsA plain beep can be mistaken for a timer or a phone. This alarm says exactly what is happening and what to do. The flame sensor watches the store room or the area near the stove, and while it sees a flame the DFPlayer repeats the warning every six seconds at full volume.
A learning project, not a certified smoke or fire alarm. Fit certified smoke detectors as well.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Infrared photodiode tuned to 760–1100 nm, the light given off by flames, with a comparator for an on/off output.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
talking_fire_alarm.inoVerify & upload in Electrolark// Talking fire alarm for a kitchen or store room
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "talking-fire-alarm"
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t FLAME_PIN = 2;
const uint8_t MP3_RX = 3;
const uint8_t MP3_TX = 4;
DFRobotDFPlayerMini player;
// ---- latest readings ----
bool flame = false;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 22; // 0-30
const unsigned long QUIET_MS = 6000UL; // at least this long between messages
unsigned long lastPlay = 0;
bool played = false;
void setup() {
Serial.begin(115200);
pinMode(FLAME_PIN, INPUT);
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
randomSeed(analogRead(A0));
}
void loop() {
flame = digitalRead(FLAME_PIN) == LOW;
if ((flame) && (!played || millis() - lastPlay > QUIET_MS)) {
int t = 1;
player.playMp3Folder(t); // plays /mp3/000t.mp3
played = true; lastPlay = millis();
Serial.print(F("Fire: track ")); Serial.println(t);
}
delay(100);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Sunlight contains strong IR. Shade the sensor or lower the sensitivity with the trimmer.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Flame Sensor Module – LM393, Digital/Analog Output, DFPlayer Mini MP3 Player Module (MP3-TF-16P), Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (talking_fire_alarm.ino). Install this library first: DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹987 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Comparator outputs and sensitivity trimmers; Serial-controlled audio playback.
A learning project, not a certified smoke or fire alarm. Fit certified smoke detectors as well.
Ideas that reuse this build: Flame fire alarm and Fire SMS alert. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.