Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe TTP223 pad works through a thin wooden or plastic lid, so the lamp has no visible controls. A tap steps through off, low, medium and high; a long touch moves to the next colour, starting from warm white. Hide the ring under frosted acrylic for a soft glow.
Tick anything you already have and the total updates.
Capacitive touch pad: works through thin plastic, glass or wood, so you can hide it inside an enclosure.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
touch_dimmer_lamp.inoVerify & upload in Electrolark// Touch lamp with brightness and colour
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "touch-dimmer-lamp"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t TOUCH_PIN = 2;
const uint8_t RING_PIN = 3;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
bool touched = false;
const int LEVELS[] = {0, 40, 110, 255};
int level = 0, hue = 0;
bool wasTouched = false;
unsigned long touchStart = 0;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void paint() {
uint32_t c = ring.ColorHSV((uint16_t)(hue * 65535L / 6), hue == 0 ? 0 : 200, 255); // hue 0 is warm white
if (hue == 0) c = ring.Color(255, 160, 70);
ring.setBrightness(LEVELS[level]);
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, c);
ring.show();
}
void setup() {
Serial.begin(115200);
pinMode(TOUCH_PIN, INPUT);
ring.begin();
ring.setBrightness(40);
ring.show();
paint();
}
void loop() {
bool t = digitalRead(TOUCH_PIN) == HIGH;
if (t && !wasTouched) touchStart = millis();
if (!t && wasTouched) {
if (millis() - touchStart > 700) hue = (hue + 1) % 6; // long touch: next colour
else level = (level + 1) % 4; // tap: next brightness
paint();
}
wasTouched = t;
delay(10);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Ground the enclosure or keep long wires away from the pad.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Capacitive Touch Sensor Module (TTP223), WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (touch_dimmer_lamp.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹353 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Capacitive sensing.
Ideas that reuse this build: Touch relay switch and Sunrise lamp. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.