Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe MPU6050 sits on the handle and measures pitch and roll. Each servo turns by the same angle the other way, so the platform on top stays level as your hand moves. Smoothing in the sketch stops the servos jittering. It is a simple version of how real gimbals work, and a good first project in feedback.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Six-axis motion sensor: a three-axis accelerometer that feels gravity and bumps, and a three-axis gyro that measures how fast it turns.
Moves the pan axis of the bracket.; Moves the tilt axis of the bracket.
Follow the colours: red is power, dark grey is ground, blue is a signal.
two_axis_camera_gimbal.inoVerify & upload in Electrolark// Two-axis phone camera gimbal
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "two-axis-camera-gimbal"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Servo.h>
// ---- pins ----
const uint8_t SERVO_PAN = 9;
const uint8_t SERVO_TILT = 10;
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
Servo pan, tilt; // pan servo levels the roll axis, tilt servo levels the pitch axis
const float SMOOTH = 0.2; // 0-1: lower is smoother but slower
float rollOut = 90, pitchOut = 90;
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
float gyroZNow() { return gyrEvt.gyro.z * 57.3f; } // turning speed in degrees per second
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setGyroRange(MPU6050_RANGE_500_DEG);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
pan.attach(SERVO_PAN); tilt.attach(SERVO_TILT);
pan.write(90); tilt.write(90);
}
void loop() {
pitchDeg = (readImu(), pitchDegNow());
rollDeg = rollDegNow();
rollOut += SMOOTH * (constrain(90 - rollDeg, 0, 180) - rollOut); // turn the opposite way to the tilt
pitchOut += SMOOTH * (constrain(90 + pitchDeg, 0, 180) - pitchOut);
pan.write((int)rollOut); tilt.write((int)pitchOut);
delay(15);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x68 (0x69 if AD0 is tied high).
Keep I²C wires short, add a 100 nF capacitor across VCC and GND, and mount the board away from motor wires.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, GY-521 MPU6050 6-Axis Gyro and Accelerometer Module, 2 × TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (two_axis_camera_gimbal.ino). Install these libraries first: Adafruit MPU6050, Adafruit Unified Sensor and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹701 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, gyros and tilt angles; PWM pulses and servo control.
Ideas that reuse this build: Joystick pan-tilt mount and Gesture wand servo. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.