Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe HC-SR04 sits on top of a servo and sweeps from side to side. At each angle the Uno measures the distance and plots a dot on the OLED at the right angle and range, with a sweeping line like an air-traffic display. Objects appear as arcs of dots.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
ultrasonic_radar_oled.inoVerify & upload in Electrolark// Ultrasonic radar with an OLED sweep
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "ultrasonic-radar-oled"
#include <Servo.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 4;
const uint8_t SERVO_PIN = 3;
Servo servo;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float distCm = 0;
int angle = 15, dirStep = 3;
float scan[181];
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void drawRadar() {
oled.clearDisplay();
oled.drawCircle(64, 63, 60, SSD1306_WHITE); oled.drawCircle(64, 63, 30, SSD1306_WHITE);
for (int a = 15; a <= 165; a += 3) {
if (scan[a] <= 0 || scan[a] > 60) continue;
float rad = a * 3.14159f / 180.0f;
oled.fillCircle(64 - cos(rad) * scan[a], 63 - sin(rad) * scan[a], 1, SSD1306_WHITE);
}
float rad = angle * 3.14159f / 180.0f;
oled.drawLine(64, 63, 64 - cos(rad) * 60, 63 - sin(rad) * 60, SSD1306_WHITE);
oled.setCursor(0, 0); oled.print(angle); oled.print(F("deg "));
if (scan[angle] > 0) { oled.print(scan[angle], 0); oled.print(F("cm")); }
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
servo.attach(SERVO_PIN);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
servo.write(angle);
delay(40);
distCm = readDistanceCm();
scan[angle] = distCm;
drawRadar();
angle += dirStep;
if (angle >= 165 || angle <= 15) dirStep = -dirStep;
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR04 Ultrasonic Range Finder Sensor Module, TowerPro SG90 9g Micro Servo (180°), 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (ultrasonic_radar_oled.ino). Install these libraries first: Servo, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹663 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; PWM pulses and servo control; Time-of-flight measurement with sound.
Ideas that reuse this build: Obstacle-avoiding robot and Pan-tilt mount. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.