Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsPumps burn out when they run without water. Press the button to start the pump; after 20 seconds of priming the flow sensor must see at least 0.5 L/min, or the relay switches the pump off, the LCD says DRY RUN and the buzzer sounds. A 30-minute limit stops a forgotten pump.
Mains pump motors must be wired by a qualified electrician through a suitable contactor. Do not connect mains to the relay module.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Mini pump for the bench model (a bigger pump goes through a contactor)
Follow the colours: red is power, dark grey is ground, blue is a signal.
This build switches a 3–6 V mini pump from a 4×AA holder. A mains motor needs a contactor and an electrician: keep the relay on the low-voltage side.
water_pump_dry_run_guard.inoVerify & upload in Electrolark// Water pump dry-run protector
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "water-pump-dry-run-guard"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t FLOW_PIN = 2;
const uint8_t RELAY_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t LED_RED = 5;
const uint8_t BUTTON_PIN = 6;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float flowLpm = 0;
float litres = 0;
const unsigned long PRIME_MS = 20000; // time the pump gets to start delivering water
const unsigned long NO_FLOW_MS = 5000; // stop if the flow stays below MIN_LPM this long
const unsigned long MAX_RUN_MS = 30 * 60000UL; // safety stop for a full tank or a forgotten pump
const float MIN_LPM = 0.5;
bool pumpOn = false, fault = false, wasDown = false;
unsigned long startedAt = 0, lowSince = 0, lastCheck = 0;
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void stopPump(const __FlashStringHelper* why, bool isFault) {
pumpOn = false; setRelay(false); fault = isFault;
lcd.setCursor(0, 0); lcd.print(why);
Serial.println(why);
}
void setup() {
Serial.begin(115200);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
pinMode(BUTTON_PIN, INPUT_PULLUP);
setRelay(false);
lcd.setCursor(0, 0); lcd.print(F("Press to start "));
}
void loop() {
bool down = digitalRead(BUTTON_PIN) == LOW;
if (down && !wasDown) {
if (pumpOn) stopPump(F("Stopped by hand "), false);
else { fault = false; pumpOn = true; startedAt = millis(); lowSince = 0; setRelay(true); lcd.setCursor(0, 0); lcd.print(F("Pump running ")); }
delay(30);
}
wasDown = down;
if (millis() - lastCheck >= 1000) {
lastCheck = millis();
flowLpm = readFlowLpm();
lcd.setCursor(0, 1); lcd.print(F("Flow ")); lcd.print(flowLpm, 1); lcd.print(F(" L/min "));
if (pumpOn && millis() - startedAt > PRIME_MS) {
if (flowLpm < MIN_LPM) { if (!lowSince) lowSince = millis(); if (millis() - lowSince > NO_FLOW_MS) stopPump(F("DRY RUN: stopped"), true); }
else lowSince = 0;
}
if (pumpOn && millis() - startedAt > MAX_RUN_MS) stopPump(F("Time limit: off "), false);
}
setRedLed(fault);
setBuzzer(fault && (millis() / 400) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
13 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, YF-S201 Water Flow Sensor 1–30 L/min, 5V Relay Module with Optocoupler (1 channel), LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Tactile Push Button Switch, Resistor Assortment Kit (30 Values), Mini Submersible Water Pump 3–6V with 1m tube, plus 3 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 2–3 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (water_pump_dry_run_guard.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹987 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Current-limiting resistors for LEDs; Interrupts and counting pulses; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Automatic water tank pump and Two-tank pump controller. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.