Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsMovement catches the eye. The PIR notices someone walking up, and the servo waves a cardboard hand back and forth three times, then rests for ten seconds so it does not wave non-stop in a busy shop. Children love it on a school exhibition stall too.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
waving_welcome_hand.inoVerify & upload in Electrolark// Waving welcome hand for a shop or stall
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "waving-welcome-hand"
#include <Servo.h>
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t SERVO_PIN = 3;
Servo servo;
// ---- latest readings ----
bool motion = false;
const int WAVES = 3; // back-and-forth waves per greeting
const unsigned long QUIET_MS = 10000; // wait this long before greeting again
unsigned long lastWave = 0;
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
servo.attach(SERVO_PIN);
servo.write(90);
}
void loop() {
motion = digitalRead(PIR_PIN) == HIGH;
if (motion && (lastWave == 0 || millis() - lastWave > QUIET_MS)) {
Serial.println(F("Hello!"));
for (int i = 0; i < WAVES; i++) {
for (int a = 60; a <= 120; a += 3) { servo.write(a); delay(12); }
for (int a = 120; a >= 60; a -= 3) { servo.write(a); delay(12); }
}
servo.write(90);
lastWave = millis();
}
delay(50);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), HC-SR501 PIR Motion Detector Sensor Module, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (waving_welcome_hand.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹419 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Digital inputs and sensor hold time; PWM pulses and servo control.
Ideas that reuse this build: Shop entrance welcome and Gesture wand servo. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.