GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsThe divider reads the battery voltage; the relay disconnects the charger above 14.4 V and reconnects at 13.4 V. The page shows the voltage and lets you switch the charger by hand. After power-up it starts charging once the battery is below 13.4 V; use the button to start sooner.
A 12 V battery can deliver hundreds of amps. Put an inline fuse at the battery terminal and insulate every joint before connecting.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Two resistors scale the battery voltage down by 11 so an analog pin can measure up to about 50 V safely.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Power the board from a 5 V USB charger, or from the 12 V battery through a buck converter set to 5 V. Fuse the battery lead to the divider at 500 mA.
wifi_battery_charge_cutoff.inoVerify & upload in Electrolark// Wi-Fi battery charge monitor and cut-off
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-battery-charge-cutoff"
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t VBAT_PIN = 0;
const uint8_t RELAY_PIN = 10;
const int ADC_MAX = 4095; // 12-bit analog input
const float VREF = 3.3f;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float batteryV = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
bool relayOn = false;
bool manualMode = false; // set when you press the button on the dashboard
bool alertOn = false;
const float ALERT_LEVEL = 13.4; // adjust to suit
const float HYSTERESIS = 1.0;
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Battery charge</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Battery charge</h1><div class="g" id="g"></div><button id="b" onclick="tog()">Switch</button><p class="s" id="s">Connecting…</p>
<script>const F=[["batteryV","Battery","V"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();document.getElementById('b').textContent=(d.relay?'Turn OFF':'Turn ON')+(d.auto?' (auto)':'');}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
async function tog(){const d=await(await fetch('/data')).json();await fetch('/relay?on='+(d.relay?0:1));tick()}setInterval(tick,2000);tick();</script></body></html>)HTML";
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX * 11.0f; } // 100 kΩ : 10 kΩ divider = ÷11
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void handleData() {
String j = "{";
j += "\"batteryV\":"; j += String(batteryV, 2); j += ",";
j += "\"relay\":"; j += relayOn ? "true," : "false,"; j += "\"auto\":"; j += manualMode ? "false," : "true,";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void handleRelay() {
if (server.hasArg("on")) {
manualMode = true;
relayOn = server.arg("on") == "1";
setRelay(relayOn);
}
server.send(200, "text/plain", relayOn ? "on" : "off");
}
void evaluate() {
if (!alertOn && batteryV < ALERT_LEVEL) alertOn = true;
else if (alertOn && batteryV > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Charging" : "Full: charger off";
if (!manualMode) { relayOn = alertOn; setRelay(relayOn); }
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.on("/relay", handleRelay);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
batteryV = readBatteryV();
evaluate();
Serial.print(F("Battery="));
Serial.print(batteryV, 2);
Serial.print(F("V"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Measure the real resistor values and change 11.0 to (R1 + R2) / R2.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
5 parts: ESP32-C3 SuperMini Development Board, Resistor Assortment Kit (30 Values), 5V Relay Module with Optocoupler (1 channel), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (wifi_battery_charge_cutoff.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹443 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Isolation, relays and switching higher-power loads; Voltage dividers and ADC scaling.
Ideas that reuse this build: Offline overcharge cut-off and Wi-Fi solar battery monitor. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 Battery=10.89V
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.