Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsIn North Indian winters and in air-conditioned rooms, humidity can fall low enough to dry skin and cause sore throats. The DHT22 reads the room; below 35 % the MOSFET switches a USB mist humidifier on, and it stays on until the air reaches 43 %. The green light shows when the room is comfortable.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Logic-level MOSFET used as a fast electronic switch, so a PWM pin can control a motor's speed.
10 kΩ gate pull-down; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
The MOSFET switches the 5 V supply of a USB mist humidifier (your own, under 1 A). Power the Nano and the humidifier from a 5 V 2 A USB charger.
winter_humidifier_controller.inoVerify & upload in Electrolark// Winter humidifier controller
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "winter-humidifier-controller"
#include <DHT.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t MOTOR_PIN = 3;
const uint8_t LED_GREEN = 4;
DHT dht(DHT_PIN, DHT22);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 35; // below about 35 % skin, eyes and throats dry out
const float HYSTERESIS = 8; // gap that stops rapid on/off switching
void setFan(bool on) { digitalWrite(MOTOR_PIN, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void evaluate() {
if (!(!isnan(tempC) && !isnan(humidity))) { statusText = "Sensor error"; return; }
if (!alertOn && humidity < ALERT_LEVEL) alertOn = true;
else if (alertOn && humidity > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Humidifying" : "OK";
}
void setup() {
Serial.begin(115200);
dht.begin();
pinMode(MOTOR_PIN, OUTPUT);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
evaluate();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setFan(alertOn);
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Gate and drain swapped, or the 10 kΩ gate pull-down is missing.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), DHT22 Temperature & Humidity Sensor, Power MOSFET (TO-220, IRLZ44N), Through-Hole LED Pack (Pack of 10), Diodes (Pack of 10, 1N4007), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (winter_humidifier_controller.ino). Install these libraries first: DHT sensor library and Adafruit Unified Sensor.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹481 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; MOSFET switching and flyback diodes; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Wardrobe monsoon dehumidifier and Greenhouse humidity control. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=26.9C, Humidity=55%, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.