Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsAn HC-05 Bluetooth module receives letter commands (F, B, L, R, S) from a free serial-Bluetooth car app and the Uno drives the two motors. It stops on its own if the phone goes quiet.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Dual H-bridge chip on a small board that drives two small DC motors forwards, backwards and at variable speed (600 mA per channel).
Classic Bluetooth serial module: your phone sends characters and the board receives them as if over a USB cable.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Power the motors from the lab's rechargeable 9 V pack or a 6 V battery holder into the module's VS terminal and join its GND to the Uno GND. Never run the motors from the Uno 5 V pin.
atl_bluetooth_rc_car.inoVerify & upload in Electrolark// Bluetooth phone-controlled car
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-bluetooth-rc-car"
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t ENA = 3;
const uint8_t IN1 = 2;
const uint8_t IN2 = 4;
const uint8_t IN3 = 6;
const uint8_t IN4 = 7;
const uint8_t ENB = 5;
const uint8_t BT_RX = 8;
const uint8_t BT_TX = 12;
SoftwareSerial btSerial(BT_RX, BT_TX);
int speedLevel = 200; // changed with app keys 0-9
unsigned long lastCommand = 0;
const unsigned long FAILSAFE_MS = 1500; // stop if the phone goes quiet
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
void setup() {
Serial.begin(115200);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
btSerial.begin(9600);
drive(0, 0);
}
void loop() {
if (btSerial.available()) {
char cmd = btSerial.read();
lastCommand = millis();
Serial.print(F("cmd ")); Serial.println(cmd);
switch (cmd) {
case 'F': drive(speedLevel, speedLevel); break;
case 'B': drive(-speedLevel, -speedLevel); break;
case 'L': drive(-speedLevel, speedLevel); break;
case 'R': drive(speedLevel, -speedLevel); break;
case 'G': drive(speedLevel / 3, speedLevel); break; // forward-left
case 'I': drive(speedLevel, speedLevel / 3); break; // forward-right
case 'S': drive(0, 0); break;
default:
if (cmd >= '0' && cmd <= '9') speedLevel = map(cmd - '0', 0, 9, 90, 255);
}
}
if (millis() - lastCommand > FAILSAFE_MS) drive(0, 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check that VS has the motor battery, that the battery GND joins the board GND, and that EN1 and EN2 are wired to PWM pins.
The L293D handles about 600 mA per channel. Use small BO motors, and stop if the chip is too hot to touch.
Check TXD→board RX and RXD→board TX (crossed). The module LED blinks slowly once connected.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, L293D Motor Driver Module (Breakout Board), HC-05 6-Pin Bluetooth Serial Module with Button, Resistor Assortment Kit (30 Values), BO Motor with Wheel Set, Metal Ball Caster Wheel, 9V Battery, 9V Battery Snap Connector, Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (atl_bluetooth_rc_car.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹796 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
H-bridges and PWM speed control; UART serial communication.
Ideas that reuse this build: Obstacle avoiding robot. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.