Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsThe relay holds a 12 V normally-closed valve open while the floor is dry. When the sensing board gets wet the relay drops out, the valve shuts, and the buzzer tells you why the tap stopped. Power cut? The valve closes too, which is the safe failure.
Have a plumber fit the valve on the supply line; keep all electronics off the floor.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Comb-patterned plate whose resistance drops when water bridges the tracks.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Normally-closed valve: it opens only while the relay powers it
Follow the colours: red is power, dark grey is ground, blue is a signal.
Adapter + to relay COM, relay NO to valve +, valve − to adapter −. The valve is inline on the appliance feed, after the stop tap.
auto_shutoff_valve.inoVerify & upload in Electrolark// Leak-triggered water shut-off valve
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "auto-shutoff-valve"
// ---- pins ----
const uint8_t RAIN_PIN = A0;
const uint8_t RELAY_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
int wetPct = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 20; // any water on the floor board
const float HYSTERESIS = 15; // gap that stops rapid on/off switching
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!alertOn && wetPct > ALERT_LEVEL) alertOn = true;
else if (alertOn && wetPct < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "VALVE CLOSED" : "Water on";
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
wetPct = (int)(100 - analogRead(RAIN_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Rain="));
Serial.print(wetPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dry the plate and clean off residue. Powering it only when reading slows corrosion.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HS-S09-PB Rain Sensor Kit – Analog/Digital Output, 5V Relay Module with Optocoupler (1 channel), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), 12V Solenoid Water Valve 1/2" (Normally Closed), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (auto_shutoff_valve.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,158 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads; Resistive sensing and corrosion.
Ideas that reuse this build: Alarm only, no valve and Tank overflow alarm. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Rain=71%, status=VALVE CLOSED Rain=71%, status=VALVE CLOSED
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.