LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsA battery does not fade evenly: the voltage stays flat then drops quickly. Students connect a 47 Ω 2 W resistor across a 4×AA pack as the load (about 100 mA), log the voltage every minute through the divider, and see the knee of the curve.
The load resistor gets warm: do not touch it while the test is running.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Two equal 10 kΩ resistors halve the input voltage, so the analog pin can measure up to about 10 V with good resolution at 1 to 6 V.; 47 Ω 2 W resistor as the load across the pack
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_battery_discharge.inoVerify & upload in Electrolark// How long does a battery last?
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-battery-discharge"
#include <Wire.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t VBAT_PIN = A0;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
RTC_DS3231 rtc;
// ---- latest readings ----
float batteryV = 0;
const unsigned long LOG_EVERY_MS = 60000UL; // one row per minute
unsigned long lastLog = 0;
bool cardOk = false;
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX * 2.0f; } // 10 kΩ : 10 kΩ divider = ÷2
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(batteryV, 2);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Voltage(V)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
batteryV = readBatteryV();
Serial.print(F("Voltage="));
Serial.print(batteryV, 2);
Serial.print(F("V"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Measure both resistors; the factor is (R1 + R2) / R2.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Compare alkaline and rechargeable packs.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Resistor Assortment Kit (30 Values), DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 4 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (class_battery_discharge.ino). Install these libraries first: RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,391 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Batteries; Discharge curves.
The load resistor gets warm: do not touch it while the test is running.
Ideas that reuse this build: Battery gauge. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Voltage=2.99V Voltage=2.99V Voltage=3.00V Voltage=3.00V Voltage=3.01V Voltage=2.99V Voltage=3.00V Voltage=3.00V
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.