LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsPouring a hot drink without seeing the level means burnt fingers or a spill. A small two-prong probe hangs a finger-width inside the rim; when the liquid touches it, the buzzer sounds and the handle vibrates. It works with tea, water, milk and juice, and stops as soon as the cup is lifted away.
Rinse and dry the probe after each use. Do not put the electronics in the dishwasher.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Comb-patterned plate whose resistance drops when water bridges the tracks.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
cup_full_alert_low_vision.inoVerify & upload in Electrolark// Cup-full alert for blind and low-vision users
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "cup-full-alert-low-vision"
// ---- pins ----
const uint8_t RAIN_PIN = A0;
const uint8_t BUZZER_PIN = 2;
const uint8_t VIBE_PIN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int wetPct = 0;
const unsigned long READ_EVERY_MS = 50;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 30; // the probe reads near 0 when dry and jumps as soon as the liquid touches it
const float HYSTERESIS = 10; // gap that stops rapid on/off switching
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void evaluate() {
if (!alertOn && wetPct > ALERT_LEVEL) alertOn = true;
else if (alertOn && wetPct < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "FULL" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(VIBE_PIN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
wetPct = (int)(100 - analogRead(RAIN_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Rain="));
Serial.print(wetPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setVibe(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dry the plate and clean off residue. Powering it only when reading slows corrosion.
Low-triggered module: invert the logic in setBuzzer().
Check the transistor orientation (flat face: C-B-E for BC547).
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
12 parts: Nano CH340 Development Board (Soldered), HS-S09-PB Rain Sensor Kit – Analog/Digital Output, Active Buzzer Module 3.3–5V, Coin Vibration Motor 3V, General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, TP4056 1A Li-ion Charger Module with Protection, plus 2 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (cup_full_alert_low_vision.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹821 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Resistive sensing and corrosion; Transistors as switches.
Rinse and dry the probe after each use. Do not put the electronics in the dishwasher.
Ideas that reuse this build: Water tank overflow alarm and Silent vibration doorbell. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Rain=70%, status=FULL Rain=70%, status=FULL Rain=71%, status=FULL Rain=70%, status=FULL Rain=70%, status=FULL Rain=70%, status=FULL Rain=70%, status=FULL Rain=70%, status=FULL
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.