LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsA glass fuse blows once; this one resets. The INA219 measures the current to the load and the relay cuts it if it stays above the limit for a tenth of a second, which ignores the short surge when motors start. The red light shows that it has tripped; press the button to reconnect once you have fixed the fault.
Keep a real fuse in the line as well. The relay is not fast enough to protect against a dead short.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
electronic_fuse_12v.inoVerify & upload in Electrolark// Resettable electronic fuse for 12 V circuits
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "electronic-fuse-12v"
#include <Wire.h>
#include <Adafruit_INA219.h>
// ---- pins ----
const uint8_t RELAY_PIN = 2;
const uint8_t LED_RED = 3;
const uint8_t BUTTON_PIN = 4;
Adafruit_INA219 ina;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const float TRIP_LEVEL = 1500; // mA: cut the load above this
const unsigned long TRIP_MS = 100; // must stay above the limit this long (ignores start-up surges)
bool tripped = false;
unsigned long overSince = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(LED_RED, OUTPUT);
pinMode(BUTTON_PIN, INPUT_PULLUP);
setRelay(true);
setRedLed(false);
}
void loop() {
currentMa = ina.getCurrent_mA();
if (!tripped) {
if (fabs(currentMa) > TRIP_LEVEL) { if (!overSince) overSince = millis(); } else overSince = 0;
if (overSince && millis() - overSince > TRIP_MS) {
tripped = true; setRelay(false);
Serial.print(F("TRIPPED at ")); Serial.println(currentMa, 2);
}
}
if (tripped && digitalRead(BUTTON_PIN) == LOW) { tripped = false; overSince = 0; setRelay(true); Serial.println(F("Reset")); delay(300); }
setRedLed(tripped);
static unsigned long lastLog = 0;
if (millis() - lastLog > 500) { lastLog = millis(); Serial.print(currentMa, 2); Serial.println(F(" mA")); }
delay(5);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), INA219 Current and Power Monitor Module, 5V Relay Module with Optocoupler (1 channel), Through-Hole LED Pack (Pack of 10), Tactile Push Button Switch, Resistor Assortment Kit (30 Values), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (electronic_fuse_12v.ino). Install this library first: Adafruit INA219.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹829 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads; Pull-ups and debouncing; Shunt resistors, current and power.
Ideas that reuse this build: Motor stall cut-off and DC energy meter. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
448.72 mA 448.97 mA 448.71 mA 450.53 mA 450.72 mA
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.