Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsFour patterns for Diwali, Christmas or a wedding: a flowing rainbow, orange lights that march like a row of diyas, gentle twinkles, and alternating flashes. Press the button for the next pattern. Join more strips for a balcony or doorway.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Addressable RGB LED strip: cut to length (here 30 LEDs, half a metre) and control every LED individually from one data pin.
Or a 5 V 2 A adapter: the strip needs its own supply
Follow the colours: red is power, dark grey is ground, blue is a signal.
festival_light_patterns.inoVerify & upload in Electrolark// Diwali and festival light patterns
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "festival-light-patterns"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t RING_PIN = 2;
const uint8_t BUTTON_PIN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const int RING_LEDS = 30;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
int mode = 0;
const int MODES = 4;
unsigned long frame = 0;
bool wasDown = false;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
uint32_t wheel(byte p) { // colour wheel: 0-255 runs through the rainbow
p = 255 - p;
if (p < 85) return ring.Color(255 - p * 3, 0, p * 3);
if (p < 170) { p -= 85; return ring.Color(0, p * 3, 255 - p * 3); }
p -= 170; return ring.Color(p * 3, 255 - p * 3, 0);
}
void setup() {
Serial.begin(115200);
ring.begin();
ring.setBrightness(40);
ring.show();
pinMode(BUTTON_PIN, INPUT_PULLUP);
}
void loop() {
bool down = digitalRead(BUTTON_PIN) == LOW;
if (down && !wasDown) { mode = (mode + 1) % MODES; Serial.print(F("Pattern ")); Serial.println(mode); }
wasDown = down;
frame++;
for (int i = 0; i < RING_LEDS; i++) {
uint32_t c = 0;
if (mode == 0) c = wheel((i * 256 / RING_LEDS + frame) & 255); // rainbow flow
else if (mode == 1) c = ((i + frame / 4) % 3 == 0) ? ring.Color(255, 120, 0) : 0; // marching diyas
else if (mode == 2) c = (random(20) == 0) ? ring.Color(255, 200, 80) : ring.getPixelColor(i) >> 1 & 0x7F7F7F; // twinkle
else c = ((frame / 20) % 2 == i % 2) ? ring.Color(255, 0, 60) : ring.Color(0, 120, 255); // alternate flash
ring.setPixelColor(i, c);
}
ring.show();
delay(30);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Add the 330 Ω resistor in series with DIN and share GND with the board.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), WS2812B Addressable RGB LED Strip (60 LEDs/m), Tactile Push Button Switch, Resistor Assortment Kit (30 Values), Enclosed SMPS Power Supply (12V), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (festival_light_patterns.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,038 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Pull-ups and debouncing.
Ideas that reuse this build: Sound-reactive strip and LED strip scanner. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.