LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsA DC motor turned by hand works as a generator. The INA219 measures the voltage and current into a few LEDs, and the LCD shows the power and the energy you have made so far. A class can race to light the LEDs, and then work out how long it would take to charge a phone.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
hand_crank_generator_lab.inoVerify & upload in Electrolark// Hand-crank generator energy lab
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "hand-crank-generator-lab"
#include <Wire.h>
#include <Adafruit_INA219.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
Adafruit_INA219 ina;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
double wh = 0, mah = 0;
unsigned long lastMs = 0, lastShow = 0;
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
lcd.init();
lcd.backlight();
pinMode(BUTTON_PIN, INPUT_PULLUP);
lastMs = millis();
}
void loop() {
unsigned long now = millis();
if (now - lastMs < 200) return;
float hours = (now - lastMs) / 3600000.0f; lastMs = now;
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
powerMw = ina.getPower_mW();
wh += powerMw / 1000.0 * hours; // energy = power x time
mah += currentMa * hours;
if (digitalRead(BUTTON_PIN) == LOW) { wh = 0; mah = 0; delay(300); }
if (now - lastShow < 500) return;
lastShow = now;
char a[8], w[8], buf[17];
dtostrf(busV, 5, 2, a); dtostrf(powerMw / 1000.0, 5, 2, w);
snprintf(buf, sizeof(buf), "%sV %sW ", a, w);
lcd.setCursor(0, 0); lcd.print(buf);
dtostrf(wh, 6, 2, a);
snprintf(buf, sizeof(buf), "%sWh %5dmAh", a, (int)mah);
lcd.setCursor(0, 1); lcd.print(buf);
Serial.print(busV, 2); Serial.print(F(" V, ")); Serial.print(currentMa, 0); Serial.print(F(" mA, ")); Serial.print(wh, 3); Serial.println(F(" Wh"));
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Nano CH340 Development Board (Soldered), INA219 Current and Power Monitor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Tactile Push Button Switch, TT Gear Motor (Yellow) 3–6V, Through-Hole LED Pack (Pack of 10), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (hand_crank_generator_lab.ino). Install these libraries first: Adafruit INA219 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹718 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Pull-ups and debouncing; Shunt resistors, current and power.
Ideas that reuse this build: Bicycle dynamo meter and Fruit battery. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
12.00 V, 451 mA, 0.001 Wh 12.02 V, 451 mA, 0.002 Wh 12.00 V, 449 mA, 0.003 Wh 12.00 V, 449 mA, 0.004 Wh
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.