Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsThe MQ-2 reacts to cooking smoke and fumes as well as gas. When the reading climbs past the limit, the relay starts a 12 V exhaust fan; once the air is clear again the fan keeps running for five more minutes before it stops, so the kitchen is properly aired.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Heated tin-oxide sensor that responds to LPG, smoke, butane and hydrogen.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter powers the fan through the relay contacts (COM and NO). The board runs from USB or a 5 V charger. Keep mains wiring out of this build.
kitchen_exhaust_auto_fan.inoVerify & upload in Electrolark// Automatic kitchen exhaust fan
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "kitchen-exhaust-auto-fan"
// ---- pins ----
const uint8_t GAS_PIN = A0;
const uint8_t RELAY_PIN = 2;
const uint8_t LED_YELLOW = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
int gasPct = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 30; // cooking smoke and tadka fumes push the MQ-2 well above clean air
const float HYSTERESIS = 8; // gap that stops rapid on/off switching
const unsigned long HOLD_MS = 300000; // keep the alert on this long after the last trigger
unsigned long lastTrigger = 0;
bool levelHigh = false;
const unsigned long WARMUP_MS = 60000UL; // sensor warm-up
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if (!levelHigh && gasPct > ALERT_LEVEL) levelHigh = true;
else if (levelHigh && gasPct < ALERT_LEVEL - HYSTERESIS) levelHigh = false;
if (levelHigh) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "Venting" : "Clear";
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
gasPct = (int)(analogRead(GAS_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Gas="));
Serial.print(gasPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, MQ-2 Smoke / LPG Gas Sensor Module – Analog/Digital Output, 5V Relay Module with Optocoupler (1 channel), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), 12V DC Brushless Fan 80mm (cooling fan), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (kitchen_exhaust_auto_fan.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹925 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: LPG gas leak alarm and Phone dashboard version. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Gas=29%, status=Warming up Gas=29%, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.