GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsAn MQ-2 and a relay on an ESP32-C3. Smoke above the limit runs the 12 V fan; the page shows the reading and has a manual switch.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Heated tin-oxide sensor that responds to LPG, smoke, butane and hydrogen.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter powers the fan through the relay contacts (COM and NO). The board runs from USB or a 5 V charger. Keep mains wiring out of this build.
wifi_kitchen_exhaust.inoVerify & upload in Electrolark// Wi-Fi kitchen exhaust fan
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-kitchen-exhaust"
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t GAS_PIN = 0;
const uint8_t RELAY_PIN = 10;
const int ADC_MAX = 4095; // 12-bit analog input
const float VREF = 3.3f;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
int gasPct = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
bool relayOn = false;
bool manualMode = false; // set when you press the button on the dashboard
bool alertOn = false;
const float ALERT_LEVEL = 30; // adjust to suit
const float HYSTERESIS = 8;
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Kitchen</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Kitchen</h1><div class="g" id="g"></div><button id="b" onclick="tog()">Switch</button><p class="s" id="s">Connecting…</p>
<script>const F=[["gasPct","Gas","%"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();document.getElementById('b').textContent=(d.relay?'Turn OFF':'Turn ON')+(d.auto?' (auto)':'');}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
async function tog(){const d=await(await fetch('/data')).json();await fetch('/relay?on='+(d.relay?0:1));tick()}setInterval(tick,2000);tick();</script></body></html>)HTML";
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void handleData() {
String j = "{";
j += "\"gasPct\":"; j += String(gasPct); j += ",";
j += "\"relay\":"; j += relayOn ? "true," : "false,"; j += "\"auto\":"; j += manualMode ? "false," : "true,";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void handleRelay() {
if (server.hasArg("on")) {
manualMode = true;
relayOn = server.arg("on") == "1";
setRelay(relayOn);
}
server.send(200, "text/plain", relayOn ? "on" : "off");
}
void evaluate() {
if (millis() < 60000UL) { statusText = "Warming up"; return; }
if (!alertOn && gasPct > ALERT_LEVEL) alertOn = true;
else if (alertOn && gasPct < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "Venting" : "Clear";
if (!manualMode) { relayOn = alertOn; setRelay(relayOn); }
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.on("/relay", handleRelay);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
gasPct = (int)(analogRead(GAS_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Gas="));
Serial.print(gasPct);
Serial.print(F("%"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
8 parts: ESP32-C3 SuperMini Development Board, MQ-2 Smoke / LPG Gas Sensor Module – Analog/Digital Output, 5V Relay Module with Optocoupler (1 channel), Resistor Assortment Kit (30 Values), 12V DC Brushless Fan 80mm (cooling fan), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (wifi_kitchen_exhaust.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹924 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Offline version and Wi-Fi gas monitor. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 Gas=29%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.