Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsShared switches pass germs around in schools, clinics and public toilets. An infrared sensor beside the door switches the lamp on when you wave your hand in front of it, and the light goes out thirty seconds after the last wave.
This is a low-voltage bench model. A mains lamp must be switched through a rated contactor installed by an electrician.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared LED and receiver pair that notices anything in front of it, up to about 10 to 30 cm, and pulls its output LOW when it does.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Green indicator LED for the normal state.; A bright LED stands in for the lamp in this bench model; a real mains lamp goes through a contactor
Follow the colours: red is power, dark grey is ground, blue is a signal.
For the bench model the relay switches a 12 V lamp or strip from the adapter (COM and NO). A mains street or porch light must be switched by a rated contactor that an electrician installs.
no_touch_washroom_light.inoVerify & upload in Electrolark// No-touch washroom light switch
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "no-touch-washroom-light"
// ---- pins ----
const uint8_t OBST_PIN = 2;
const uint8_t RELAY_PIN = 3;
const uint8_t LED_GREEN = 4;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
bool obstacle = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 30000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void evaluate() {
if (obstacle) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "LIGHT ON" : "Wave to light";
}
void setup() {
Serial.begin(115200);
pinMode(OBST_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
obstacle = digitalRead(OBST_PIN) == LOW;
evaluate();
Serial.print(F("Obstacle="));
Serial.print(obstacle ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the trimmer anticlockwise, point the sensor away from the floor or a nearby wall, and keep it out of direct sunlight.
Turn the trimmer clockwise and test with a white card 5 cm away; dark objects may need a shorter range.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Nano CH340 Development Board (Soldered), Infrared Obstacle Avoidance Sensor Module, 5V Relay Module with Optocoupler (1 channel), 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (no_touch_washroom_light.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹614 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads; Reflective infrared sensing.
Ideas that reuse this build: Hand-wave light switch and Touch-free hand wave bell. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Obstacle=no, status=Wave to light Obstacle=no, status=Wave to light
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.