Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsOrdinary pet flaps let any animal in. Here a small RFID tag on the collar is read by the RC522 hidden beside the flap; if it matches one of your pets, the servo pulls the latch back for eight seconds. Unknown tags are ignored and printed in the Serial Monitor so you can add new pets.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
13.56 MHz RFID/NFC reader that reads the unique ID of cards and key fobs held near it.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rfid_pet_door.inoVerify & upload in Electrolark// RFID cat flap that only opens for your pet
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "rfid-pet-door"
#include <SPI.h>
#include <MFRC522.h>
#include <Servo.h>
// ---- pins ----
const uint8_t RFID_SS = 2;
const uint8_t RFID_RST = 4;
const uint8_t SERVO_PIN = 3;
const uint8_t LED_GREEN = 5;
MFRC522 rfid(RFID_SS, RFID_RST);
Servo servo;
// Add the UIDs of your pets' collar tags here (printed in the Serial Monitor when a tag is read)
const byte PETS[][4] = {
{0xDE, 0xAD, 0xBE, 0xEF},
};
const int LOCKED_ANGLE = 0, OPEN_ANGLE = 80;
const unsigned long OPEN_MS = 8000; // time for the pet to push through the flap
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
bool isPet(const byte* uid) {
for (unsigned int i = 0; i < sizeof(PETS) / sizeof(PETS[0]); i++)
if (memcmp(uid, PETS[i], 4) == 0) return true;
return false;
}
void setup() {
Serial.begin(115200);
SPI.begin();
rfid.PCD_Init();
servo.attach(SERVO_PIN);
pinMode(LED_GREEN, OUTPUT);
servo.write(LOCKED_ANGLE);
}
void loop() {
if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) return;
for (byte i = 0; i < rfid.uid.size; i++) { if (rfid.uid.uidByte[i] < 0x10) Serial.print('0'); Serial.print(rfid.uid.uidByte[i], HEX); Serial.print(' '); }
Serial.println();
if (rfid.uid.size >= 4 && isPet(rfid.uid.uidByte)) {
setGreenLed(true); servo.write(OPEN_ANGLE); // unlatch the flap
delay(OPEN_MS);
servo.write(LOCKED_ANGLE); setGreenLed(false);
}
rfid.PICC_HaltA();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check it is on 3.3 V and the SPI wires (SCK, MOSI, MISO) are on the hardware SPI pins.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, RC522 RFID Reader / Writer SPI Module with Card & Tag, TowerPro SG90 9g Micro Servo (180°), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (rfid_pet_door.ino). Install these libraries first: MFRC522 and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹536 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; PWM pulses and servo control; RFID, UIDs and SPI.
Ideas that reuse this build: RFID door lock and Scheduled pet feeder. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.