Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsA proper thermostat with a dial. The LCD shows the room temperature and the target; each click of the encoder moves the target half a degree. A one-degree band around the set point stops the relay clicking on and off. Control a low-voltage heater, a fan or a pump.
Switch only low-voltage loads unless an electrician fits the relay in an earthed enclosure.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rotary_thermostat_lcd.inoVerify & upload in Electrolark// Room thermostat with a rotary knob
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "rotary-thermostat-lcd"
#include <DHT.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t ENC_CLK = 3;
const uint8_t ENC_DT = 4;
const uint8_t ENC_SW = 5;
const uint8_t RELAY_PIN = 6;
DHT dht(DHT_PIN, DHT22);
LiquidCrystal_I2C lcd(0x27, 16, 2);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
float setpoint = 24.0;
const float HYST = 0.5;
bool heating = false;
int lastClk = HIGH;
unsigned long lastRead = 0, lastShow = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void show() {
lcd.setCursor(0, 0); lcd.print(F("Room ")); lcd.print(tempC, 1); lcd.print((char)223); lcd.print(F("C "));
lcd.setCursor(0, 1); lcd.print(F("Set ")); lcd.print(setpoint, 1); lcd.print((char)223); lcd.print(heating ? F("C HEAT") : F("C "));
}
void setup() {
Serial.begin(115200);
dht.begin();
pinMode(ENC_CLK, INPUT_PULLUP);
pinMode(ENC_DT, INPUT_PULLUP);
pinMode(ENC_SW, INPUT_PULLUP);
lcd.init();
lcd.backlight();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lastClk = digitalRead(ENC_CLK);
setRelay(false);
}
void loop() {
int clk = digitalRead(ENC_CLK);
if (clk != lastClk && clk == LOW) { setpoint += (digitalRead(ENC_DT) != clk) ? 0.5f : -0.5f; setpoint = constrain(setpoint, 10, 35); show(); }
lastClk = clk;
if (millis() - lastRead > 2000) {
lastRead = millis();
tempC = dht.readTemperature();
if (!isnan(tempC)) {
if (!heating && tempC < setpoint - HYST) heating = true;
if (heating && tempC > setpoint + HYST) heating = false;
setRelay(heating);
show();
Serial.print(tempC, 1); Serial.print(F(" C, set ")); Serial.print(setpoint, 1); Serial.println(heating ? F(" HEAT") : F(" idle"));
}
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Turn slower, or add 100 nF capacitors from CLK and DT to GND to debounce.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DHT22 Temperature & Humidity Sensor, KY-040 Incremental Rotary Encoder Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), 5V Relay Module with Optocoupler (1 channel), Enclosed SMPS Power Supply (12V), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (rotary_thermostat_lcd.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹937 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Isolation, relays and switching higher-power loads; Quadrature encoders; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Fan controller and Wi-Fi thermostat. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
26.9 C, set 24.0 idle
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.