GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsBelow 21 °C the relay switches a low-voltage heater or heat mat on, and it switches off again at 22 °C. The dashboard shows temperature, humidity and the heater state; tap the button to take manual control.
Switch only low-voltage heaters with this relay module.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
wifi_thermostat.inoVerify & upload in Electrolark// Wi-Fi thermostat with manual override
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-thermostat"
#include <DHT.h>
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t DHT_PIN = 10;
const uint8_t RELAY_PIN = 7;
DHT dht(DHT_PIN, DHT22);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
bool relayOn = false;
bool manualMode = false; // set when you press the button on the dashboard
bool alertOn = false;
const float ALERT_LEVEL = 21; // adjust to suit
const float HYSTERESIS = 1;
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Thermostat</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Thermostat</h1><div class="g" id="g"></div><button id="b" onclick="tog()">Switch</button><p class="s" id="s">Connecting…</p>
<script>const F=[["tempC","Temp","C"],["humidity","Humidity","%"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();document.getElementById('b').textContent=(d.relay?'Turn OFF':'Turn ON')+(d.auto?' (auto)':'');}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
async function tog(){const d=await(await fetch('/data')).json();await fetch('/relay?on='+(d.relay?0:1));tick()}setInterval(tick,2000);tick();</script></body></html>)HTML";
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void handleData() {
String j = "{";
j += "\"tempC\":"; j += String(tempC, 1); j += ",";
j += "\"humidity\":"; j += String(humidity, 0); j += ",";
j += "\"relay\":"; j += relayOn ? "true," : "false,"; j += "\"auto\":"; j += manualMode ? "false," : "true,";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void handleRelay() {
if (server.hasArg("on")) {
manualMode = true;
relayOn = server.arg("on") == "1";
setRelay(relayOn);
}
server.send(200, "text/plain", relayOn ? "on" : "off");
}
void evaluate() {
if (!(!isnan(tempC) && !isnan(humidity))) { statusText = "Sensor error"; return; }
if (!alertOn && tempC < ALERT_LEVEL) alertOn = true;
else if (alertOn && tempC > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Heating" : "Warm enough";
if (!manualMode) { relayOn = alertOn; setRelay(relayOn); }
}
void setup() {
Serial.begin(115200);
dht.begin();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.on("/relay", handleRelay);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
evaluate();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
6 parts: ESP32-C3 SuperMini Development Board, DHT22 Temperature & Humidity Sensor, 5V Relay Module with Optocoupler (1 channel), Enclosed SMPS Power Supply (12V), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (wifi_thermostat.ino). Install these libraries first: DHT sensor library and Adafruit Unified Sensor.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹796 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Isolation, relays and switching higher-power loads; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Knob and LCD version and Reptile heat mat. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 Temp=26.9C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.