GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsA turbidity probe in a clear flow pot at the outlet checks the water clarity. When it falls below the limit an SMS goes out, so you can stop the pump before silt reaches the tank or the drip lines.
Put your own number in PHONE before uploading. The project needs a SIM with SMS credit on a network that still offers 2G where you live.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Shines light through the water gap and measures how much gets through.
A small 2G phone module: with a SIM card it sends and receives SMS, so the project can alert you or take commands from anywhere with mobile coverage.
1 kΩ + 2 kΩ divider on the RXD line from a 5 V board; 1 kΩ + 2 kΩ divider for the 3.3 V input
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
The SIM800L runs straight from the 18650 cell (VCC and GND), never from the board's 5 V pin. Join the cell − to the board GND. A capacitor of 470–1000 µF across the module's VCC and GND stops resets. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
sms_borewell_muddy_water_alert.inoVerify & upload in Electrolark// Borewell muddy water SMS alert
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "sms-borewell-muddy-water-alert"
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t TURB_PIN = A0;
const uint8_t GSM_RX = 2;
const uint8_t GSM_TX = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int clarityPct = 0;
SoftwareSerial gsm(GSM_RX, GSM_TX);
const char PHONE[] = "+91XXXXXXXXXX"; // your mobile number, with the country code
const unsigned long MIN_GAP_MS = 30 * 60000UL; // never more than one SMS in this time
bool alarm = false;
unsigned long lastSms = 0, lastRead = 0;
bool sentOnce = false;
void sendSms(const String& text) {
gsm.println(F("AT+CMGF=1")); delay(300);
gsm.print(F("AT+CMGS=\"")); gsm.print(PHONE); gsm.println('"'); delay(500);
gsm.print(text); gsm.write(26); // Ctrl+Z sends the message
delay(4000);
while (gsm.available()) Serial.write(gsm.read());
Serial.print(F("SMS sent: ")); Serial.println(text);
}
void setup() {
Serial.begin(115200);
gsm.begin(9600);
delay(3000); // give the module time to find the network
gsm.println(F("AT+CMGF=1")); delay(300); // SMS in text mode
gsm.println(F("AT+CNMI=2,2,0,0,0")); delay(300); // print new SMS straight to the serial line
}
void loop() {
while (gsm.available()) Serial.write(gsm.read()); // show the module's replies
if (millis() - lastRead < 1000) return;
lastRead = millis();
clarityPct = (int)(analogRead(TURB_PIN) * 100L / ADC_MAX);
if (!alarm && (clarityPct < 40 && millis() > 30000)) {
alarm = true;
if (!sentOnce || millis() - lastSms > MIN_GAP_MS) { sendSms(String("Borewell water is muddy (") + String(clarityPct) + ")"); lastSms = millis(); sentOnce = true; }
} else if (alarm && (clarityPct > 55)) {
alarm = false; Serial.println(F("Back to normal"));
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Shade the sensor gap; stray light adds to the reading.
The supply sags during transmit bursts. Use a good 18650 cell, short thick wires and a large capacitor.
Once every 3 seconds means registered. If it never registers, the SIM's network may have switched 2G off in your area.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Asair AZDM01 Turbidity Sensor Module – Analog, SIM800L GPRS GSM Module Core Board with Antenna, Resistor Assortment Kit (30 Values), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (sms_borewell_muddy_water_alert.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,196 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
AT commands and SMS; Optical sensing and calibration references.
Put your own number in PHONE before uploading. The project needs a SIM with SMS credit on a network that still offers 2G where you live.
Ideas that reuse this build: Borewell water clarity logger and Muddy water drain valve. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.