GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsThe thermocouple on the flue pipe reads the surface temperature. Above 250 °C the buzzer sounds and an SMS tells the cook or owner to close the air inlet, a useful guard against chimney fires in a busy kitchen.
Keep the board and SIM module away from the hot pipe, and follow the stove maker's limits.
Put your own number in PHONE before uploading. The project needs a SIM with SMS credit on a network that still offers 2G where you live.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Reads a K-type thermocouple probe up to 1,000 °C through an amplifier chip, which is the way to measure ovens, kilns, soldering irons and engines.
A small 2G phone module: with a SIM card it sends and receives SMS, so the project can alert you or take commands from anywhere with mobile coverage.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
1 kΩ + 2 kΩ divider on the RXD line from a 5 V board; 1 kΩ + 2 kΩ divider for the 3.3 V input
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
The SIM800L runs straight from the 18650 cell (VCC and GND), never from the board's 5 V pin. Join the cell − to the board GND. A capacitor of 470–1000 µF across the module's VCC and GND stops resets. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
sms_flue_overheat_alert.inoVerify & upload in Electrolark// Flue overheat SMS alert
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "sms-flue-overheat-alert"
#include <max6675.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t TC_SCK = 2;
const uint8_t TC_CS = 3;
const uint8_t TC_SO = 4;
const uint8_t GSM_RX = 5;
const uint8_t GSM_TX = 6;
const uint8_t BUZZER_PIN = 7;
MAX6675 thermocouple(TC_SCK, TC_CS, TC_SO);
// ---- latest readings ----
float probeC = 0;
SoftwareSerial gsm(GSM_RX, GSM_TX);
const char PHONE[] = "+91XXXXXXXXXX"; // your mobile number, with the country code
const unsigned long MIN_GAP_MS = 30 * 60000UL; // never more than one SMS in this time
bool alarm = false;
unsigned long lastSms = 0, lastRead = 0;
bool sentOnce = false;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void sendSms(const String& text) {
gsm.println(F("AT+CMGF=1")); delay(300);
gsm.print(F("AT+CMGS=\"")); gsm.print(PHONE); gsm.println('"'); delay(500);
gsm.print(text); gsm.write(26); // Ctrl+Z sends the message
delay(4000);
while (gsm.available()) Serial.write(gsm.read());
Serial.print(F("SMS sent: ")); Serial.println(text);
}
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
gsm.begin(9600);
delay(3000); // give the module time to find the network
gsm.println(F("AT+CMGF=1")); delay(300); // SMS in text mode
gsm.println(F("AT+CNMI=2,2,0,0,0")); delay(300); // print new SMS straight to the serial line
}
void loop() {
while (gsm.available()) Serial.write(gsm.read()); // show the module's replies
if (millis() - lastRead < 1000) return;
lastRead = millis();
probeC = thermocouple.readCelsius();
if (!alarm && (probeC > 250)) {
alarm = true;
if (!sentOnce || millis() - lastSms > MIN_GAP_MS) { sendSms(String("Flue too hot (") + String(probeC) + ")"); lastSms = millis(); sentOnce = true; }
} else if (alarm && (probeC < 220)) {
alarm = false; Serial.println(F("Back to normal"));
}
setBuzzer(alarm);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The thermocouple is not connected or its plus and minus wires are swapped. Check the screw terminals.
The module also senses its own temperature at the cold junction. Keep it away from the heat you are measuring.
The supply sags during transmit bursts. Use a good 18650 cell, short thick wires and a large capacitor.
Once every 3 seconds means registered. If it never registers, the SIM's network may have switched 2G off in your area.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, MAX6675 Module with K-Type Thermocouple Probe, 50 cm Cable, SIM800L GPRS GSM Module Core Board with Antenna, Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (sms_flue_overheat_alert.ino). Install this library first: MAX6675 library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,243 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
AT commands and SMS; Active vs passive buzzers; Thermocouples and cold-junction compensation.
Keep the board and SIM module away from the hot pipe, and follow the stove maker's limits. Put your own number in PHONE before uploading. The project needs a SIM with SMS credit on a network that still offers 2G where you live.
Ideas that reuse this build: Chimney flue temperature alarm and Pizza and tandoor oven ready alert. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.