GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsWalking to the field at night to switch the pump on is a daily chore for many farmers. With a SIM800L the Uno receives text messages: ON starts the pump, OFF stops it and STATUS asks for the state, and it always replies to confirm. It obeys only your number, and switches itself off after two hours in case an OFF message goes astray.
The relay drives the pump starter's control circuit only. A licensed electrician must wire the starter and contactor; never connect the motor to the relay module.
Put your own number in PHONE before uploading. The project needs a SIM with SMS credit on a network that still offers 2G where you live.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A small 2G phone module: with a SIM card it sends and receives SMS, so the project can alert you or take commands from anywhere with mobile coverage.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
1 kΩ + 2 kΩ divider on the RXD line from a 5 V board; 1 kΩ + 2 kΩ divider for the 3.3 V input
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
The SIM800L runs straight from the 18650 cell (VCC and GND), never from the board's 5 V pin. Join the cell − to the board GND. A capacitor of 470–1000 µF across the module's VCC and GND stops resets. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
sms_pump_remote_switch.inoVerify & upload in Electrolark// SMS pump remote switch
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "sms-pump-remote-switch"
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t GSM_RX = 2;
const uint8_t GSM_TX = 3;
const uint8_t RELAY_PIN = 4;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
SoftwareSerial gsm(GSM_RX, GSM_TX);
const char PHONE[] = "+91XXXXXXXXXX"; // your mobile number, with the country code
const unsigned long MAX_ON_MS = 120 * 60000UL; // switch off by itself after 2 hours, in case the OFF message is lost
bool on = false;
unsigned long onSince = 0;
String line, sender;
bool nextIsBody = false;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void sendSms(const String& text) {
gsm.println(F("AT+CMGF=1")); delay(300);
gsm.print(F("AT+CMGS=\"")); gsm.print(PHONE); gsm.println('"'); delay(500);
gsm.print(text); gsm.write(26); // Ctrl+Z sends the message
delay(4000);
while (gsm.available()) Serial.write(gsm.read());
Serial.print(F("SMS sent: ")); Serial.println(text);
}
void reply() {
String msg = String("Pump ") + (on ? "ON" : "OFF");
sendSms(msg);
}
void handle(String body) {
body.trim(); body.toUpperCase();
if (sender.indexOf(String(PHONE).substring(3)) < 0) { Serial.println(F("Ignored: not the owner")); return; } // only obey your own number
if (body == "ON") { on = true; onSince = millis(); }
else if (body == "OFF") on = false;
else if (body != "STATUS") return;
setRelay(on);
reply();
}
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
gsm.begin(9600);
delay(3000); // give the module time to find the network
gsm.println(F("AT+CMGF=1")); delay(300); // SMS in text mode
gsm.println(F("AT+CNMI=2,2,0,0,0")); delay(300); // print new SMS straight to the serial line
setRelay(false);
}
void loop() {
while (gsm.available()) {
char ch = gsm.read();
if (ch == '\n') {
line.trim();
if (nextIsBody) { nextIsBody = false; handle(line); }
else if (line.startsWith("+CMT:")) { // +CMT: "+91XXXXXXXXXX","","date"
int a = line.indexOf('"') + 1; sender = line.substring(a, line.indexOf('"', a)); nextIsBody = true;
}
if (line.length()) Serial.println(line);
line = "";
} else if (ch != '\r') line += ch;
}
if (on && millis() - onSince > MAX_ON_MS) { on = false; setRelay(false); sendSms("Switched OFF after the time limit"); }
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The supply sags during transmit bursts. Use a good 18650 cell, short thick wires and a large capacitor.
Once every 3 seconds means registered. If it never registers, the SIM's network may have switched 2G off in your area.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, SIM800L GPRS GSM Module Core Board with Antenna, 5V Relay Module with Optocoupler (1 channel), Resistor Assortment Kit (30 Values), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (sms_pump_remote_switch.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,011 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
AT commands and SMS; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: With a tank level report and Wi-Fi smart switch. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.