Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsMint, curry leaves and chilli dry faster and keep better colour in warm air than in the sun, but too much heat spoils the flavour. The probe sits in the drying box, and below 45 °C the relay heats a 12 V pad; at 50 °C it switches off. The yellow light shows heating. Bench model only.
A heating pad is a fire risk. Use only a pad rated for the box, fuse the 12 V line at 3 A, and never leave a dryer running unattended.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
4.7 kΩ pull-up between DATA and VCC; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
The 12 V adapter feeds the heating pad through the relay (COM and NO). Use a pad of 20 W or less with this relay module, and fuse the 12 V line at 3 A.
spice_dryer_heater_controller.inoVerify & upload in Electrolark// Small spice and herb dryer controller
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "spice-dryer-heater-controller"
#include <OneWire.h>
#include <DallasTemperature.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t RELAY_PIN = 3;
const uint8_t LED_YELLOW = 4;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 3000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 45; // herbs and spices dry best at a steady 45 to 50 °C
const float HYSTERESIS = 5; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC < ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Heating" : "At temperature";
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, 5V Relay Module with Optocoupler (1 channel), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), 12V Silicone Heating Pad (100 × 100mm), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (spice_dryer_heater_controller.ino). Install these libraries first: OneWire and DallasTemperature.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹873 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Seed germination heater and Reptile tank heater. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.