Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsThe ultrasonic sensor watches the lane in front of the barrier. When a toy car comes within 10 cm, the servo swings the boom up; three seconds after the lane is clear it comes back down. A favourite for smart-city and science-fair models.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
toll_gate_boom_barrier_model.inoVerify & upload in Electrolark// Toll gate boom barrier model
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "toll-gate-boom-barrier-model"
#include <Servo.h>
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 4;
const uint8_t SERVO_PIN = 3;
Servo servo;
// ---- latest readings ----
float distCm = 0;
const int TRIGGER_CM = 10; // hand closer than this triggers
const int REST_ANGLE = 0;
const int ACTIVE_ANGLE = 90;
const unsigned long HOLD_MS = 3000;
unsigned long activatedAt = 0;
bool active = false;
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
servo.attach(SERVO_PIN);
servo.write(REST_ANGLE);
}
void loop() {
distCm = readDistanceCm();
if (distCm > 0 && distCm < TRIGGER_CM) {
if (!active) Serial.println(F("Vehicle: raising barrier"));
active = true;
activatedAt = millis();
}
if (active && millis() - activatedAt > HOLD_MS) active = false;
servo.write(active ? ACTIVE_ANGLE : REST_ANGLE);
delay(80);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR04 Ultrasonic Range Finder Sensor Module, TowerPro SG90 9g Micro Servo (180°), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (toll_gate_boom_barrier_model.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹496 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
PWM pulses and servo control; Time-of-flight measurement with sound.
Ideas that reuse this build: Automatic dustbin lid and Traffic light model. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.