LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsThe INA219 measures the voltage and the current through a resistor at the same time. Change the supply from 1.5 V to 6 V with AA cells and the current changes in step, so V divided by I stays the resistance. Swap resistors to compare.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + goes to VIN+, VIN− goes through the resistor back to battery −, and battery − joins the board GND. Power the Uno from USB.
class_ohms_law_lab.inoVerify & upload in Electrolark// Ohm's law with a power monitor
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-ohms-law-lab"
#include <Wire.h>
#include <Adafruit_INA219.h>
#include <LiquidCrystal_I2C.h>
Adafruit_INA219 ina;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const unsigned long READ_EVERY_MS = 300;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Voltage "));
lcd.print(busV, 2);
lcd.print(F(" V"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Current "));
lcd.print(currentMa, 0);
lcd.print(F(" mA"));
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
powerMw = ina.getPower_mW();
Serial.print(F("Voltage="));
Serial.print(busV, 2);
Serial.print(F("V"));
Serial.print(F(", Current="));
Serial.print(currentMa, 0);
Serial.print(F("mA"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use 100 Ω and 220 Ω resistors with 1 to 4 AA cells, and keep the current under 100 mA. Students plot V against I; the slope is the resistance.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, INA219 Current and Power Monitor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_ohms_law_lab.ino). Install these libraries first: Adafruit INA219 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹713 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Voltage, current and resistance; Ohm's law.
Ideas that reuse this build: Voltage divider lab and DIY USB power meter. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
V, Current=451mA Voltage=12.02V, Current=448mA Voltage=12.00V, Current=452mA Voltage=12.02V, Current=451mA Voltage=11.99V, Current=450mA Voltage=11.98V, Current=451mA
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.