Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsRun the obstacle-avoiding robot with different thresholds and score how many walls it hits. Students tune the stopping distance to find the best compromise between safety and speed.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Small hobby servo that turns to any angle from 0 to 180° on command.
Dual H-bridge that lets the board drive two DC motors forwards, backwards and at variable speed.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Join the two cells in series (7.4 V) and connect the pack to the L298N 12V and GND terminals. With the 5V-EN jumper fitted, the L298N 5V terminal powers the Uno: wire it to the Uno 5V pin. Join all the GND wires together. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
class_robot_bump_test.inoVerify & upload in Electrolark// Robot obstacle test course
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-robot-bump-test"
#include <Servo.h>
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 4;
const uint8_t SERVO_PIN = 3;
const uint8_t ENA = 5;
const uint8_t IN1 = 7;
const uint8_t IN2 = 8;
const uint8_t IN3 = 12;
const uint8_t IN4 = 13;
const uint8_t ENB = 6;
Servo servo;
// ---- latest readings ----
float distCm = 0;
const int SAFE_CM = 25; // stop and look around when something is closer
const int SPEED = 160;
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
float lookAt(int angle) {
servo.write(angle);
delay(350); // give the servo time to arrive
float d = readDistanceCm();
return d < 0 ? 400 : d; // no echo means open space
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
servo.attach(SERVO_PIN);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
servo.write(90);
drive(0, 0);
delay(2000);
}
void loop() {
distCm = readDistanceCm();
if (distCm < 0 || distCm > SAFE_CM) {
drive(SPEED, SPEED);
delay(40);
return;
}
drive(0, 0);
drive(-SPEED, -SPEED); // back off a little
delay(250);
drive(0, 0);
float leftCm = lookAt(160);
float rightCm = lookAt(20);
servo.write(90);
Serial.print(F("left=")); Serial.print(leftCm); Serial.print(F(" right=")); Serial.println(rightCm);
if (leftCm > rightCm) drive(-SPEED, SPEED); else drive(SPEED, -SPEED);
delay(350); // about a quarter turn: tune for your chassis
drive(0, 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
The ENA/ENB jumpers must be removed and wired to PWM pins, and the battery GND must connect to the board GND.
Swap that motor's two wires on the screw terminal.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Mark a 2 m course; count collisions over five runs.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR04 Ultrasonic Range Finder Sensor Module, TowerPro SG90 9g Micro Servo (180°), L298N Dual H-Bridge Motor Driver Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (class_robot_bump_test.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,308 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Tuning; Testing.
Ideas that reuse this build: Obstacle-avoiding robot. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.