Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsThe L298N drops about 2 V inside itself, which is a big slice of a 7.4 V battery. The TB6612FNG uses MOSFETs and loses almost nothing, so the motors spin faster and the battery lasts longer. Paired with a Nano, the whole robot fits on a smaller chassis.
Tick anything you already have and the total updates.
Three infrared reflectance sensors in a row: the centre one should see the tape, and the outer two tell the robot which way it has drifted.
Compact MOSFET motor driver that wastes far less power than an L298N, so battery robots run longer and the motors get more voltage.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
line_follower_tb6612.inoVerify & upload in Electrolark// Line follower with an efficient TB6612 driver
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "line-follower-tb6612"
// ---- pins ----
const uint8_t LINE_L = 2;
const uint8_t LINE_C = 4;
const uint8_t LINE_R = 6;
const uint8_t ENA = 3;
const uint8_t IN1 = 7;
const uint8_t IN2 = 8;
const uint8_t ENB = 5;
const uint8_t IN3 = 12;
const uint8_t IN4 = 13;
const uint8_t STBY_PIN = 9;
const int BASE_SPEED = 150; // 0-255, lower it if the robot overshoots
const int TURN_SPEED = 110;
int lastDir = 0; // remembers which way the line went when it was lost
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
void setup() {
Serial.begin(115200);
pinMode(LINE_L, INPUT); pinMode(LINE_C, INPUT); pinMode(LINE_R, INPUT);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
pinMode(STBY_PIN, OUTPUT); digitalWrite(STBY_PIN, HIGH);
}
void loop() {
bool l = digitalRead(LINE_L) == LOW, cC = digitalRead(LINE_C) == LOW, r = digitalRead(LINE_R) == LOW; // LOW = sees black
if (cC && !l && !r) { drive(BASE_SPEED, BASE_SPEED); }
else if (l && !r) { drive(BASE_SPEED - TURN_SPEED, BASE_SPEED); lastDir = -1; }
else if (r && !l) { drive(BASE_SPEED, BASE_SPEED - TURN_SPEED); lastDir = 1; }
else if (l && cC && r) { drive(0, 0); delay(300); } // a crossbar: stop briefly
else if (!l && !cC && !r) { if (lastDir < 0) drive(-TURN_SPEED, TURN_SPEED); else drive(TURN_SPEED, -TURN_SPEED); } // lost: spin back
delay(10);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Lower the sensor, re-tune the trimmers over the tape, and slow BASE_SPEED down.
STBY is floating or LOW: wire it to a pin held HIGH (the sketch does this) or to VCC.
Swap that motor's two wires on the driver.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Nano CH340 Development Board (Soldered), 3-Channel Path Tracing IR Sensor Module, TB6612FNG Dual Motor Driver Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (line_follower_tb6612.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,282 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
MOSFET H-bridges and standby pins; Multi-sensor line following.
Ideas that reuse this build: L298N version and Bluetooth car. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.