Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsTwo sensors tell a robot it has drifted; three tell it how far. With the centre sensor on the line the robot drives straight at full speed, an outer sensor makes it turn, and if it loses the line it spins back the way it last saw it. It also stops briefly at a crossbar.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Three infrared reflectance sensors in a row: the centre one should see the tape, and the outer two tell the robot which way it has drifted.
Dual H-bridge that lets the board drive two DC motors forwards, backwards and at variable speed.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Join the two cells in series (7.4 V) and connect the pack to the L298N 12V and GND terminals. With the 5V-EN jumper fitted, the L298N 5V terminal powers the Uno: wire it to the Uno 5V pin. Join all the GND wires together. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
three_sensor_line_follower.inoVerify & upload in Electrolark// Fast line follower with three sensors
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "three-sensor-line-follower"
// ---- pins ----
const uint8_t LINE_L = 2;
const uint8_t LINE_C = 4;
const uint8_t LINE_R = 6;
const uint8_t ENA = 3;
const uint8_t IN1 = 7;
const uint8_t IN2 = 8;
const uint8_t IN3 = 12;
const uint8_t IN4 = 13;
const uint8_t ENB = 5;
const int BASE_SPEED = 150; // 0-255, lower it if the robot overshoots
const int TURN_SPEED = 110;
int lastDir = 0; // remembers which way the line went when it was lost
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
void setup() {
Serial.begin(115200);
pinMode(LINE_L, INPUT); pinMode(LINE_C, INPUT); pinMode(LINE_R, INPUT);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
}
void loop() {
bool l = digitalRead(LINE_L) == LOW, cC = digitalRead(LINE_C) == LOW, r = digitalRead(LINE_R) == LOW; // LOW = sees black
if (cC && !l && !r) { drive(BASE_SPEED, BASE_SPEED); }
else if (l && !r) { drive(BASE_SPEED - TURN_SPEED, BASE_SPEED); lastDir = -1; }
else if (r && !l) { drive(BASE_SPEED, BASE_SPEED - TURN_SPEED); lastDir = 1; }
else if (l && cC && r) { drive(0, 0); delay(300); } // a crossbar: stop briefly
else if (!l && !cC && !r) { if (lastDir < 0) drive(-TURN_SPEED, TURN_SPEED); else drive(TURN_SPEED, -TURN_SPEED); } // lost: spin back
delay(10);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Lower the sensor, re-tune the trimmers over the tape, and slow BASE_SPEED down.
The ENA/ENB jumpers must be removed and wired to PWM pins, and the battery GND must connect to the board GND.
Swap that motor's two wires on the screw terminal.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 3-Channel Path Tracing IR Sensor Module, L298N Dual H-Bridge Motor Driver Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3–4 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (three_sensor_line_follower.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,331 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Multi-sensor steering; Remembering state; H-bridge speed control.
Ideas that reuse this build: Two-sensor version and TB6612 low-loss driver version. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.