GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsMushroom huts are usually away from the house. The node sends temperature and humidity every minute and adds ALERT when humidity drops below 80 %.
Tick anything you already have and the total updates.
Long-range 433 MHz radio that sends small messages a kilometre or more across open fields with very little power.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Charges the cell, from a small solar panel if you like
Follow the colours: red is power, dark grey is ground, blue is a signal.
Cell to the TP4056 B+ and B−; TP4056 OUT+ to the ESP32-C3 5V pin and OUT− to GND. The board's own regulator makes 3.3 V from the cell, and the LoRa module takes its 3.3 V from the board. Put the node in a sealed box with the antenna outside and upright.
lora_mushroom_hut_node.inoVerify & upload in Electrolark// LoRa mushroom hut node
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "lora-mushroom-hut-node"
#include <SPI.h>
#include <LoRa.h>
#include <DHT.h>
// ---- pins ----
const uint8_t LORA_RST = 10;
const uint8_t LORA_DIO0 = 3;
const uint8_t DHT_PIN = 2;
DHT dht(DHT_PIN, DHT22);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const char NODE[] = "MUSHR"; // the receiver shows this name
const unsigned long SEND_EVERY_MS = 60000UL;
unsigned long lastSend = 0;
bool wasAlarm = false;
void setup() {
Serial.begin(115200);
LoRa.setPins(SS, LORA_RST, LORA_DIO0);
if (!LoRa.begin(433E6)) Serial.println(F("LoRa module not found"));
LoRa.setSpreadingFactor(10); // slower but reaches further
dht.begin();
}
void loop() {
tempC = dht.readTemperature();
humidity = dht.readHumidity();
String msg = String(NODE) + ";" + String("tempC=") + String(tempC) + ";" + String("humidity=") + String(humidity);
bool alarm = humidity < 80;
if (alarm) msg += ";ALERT";
bool urgent = alarm && !wasAlarm;
wasAlarm = alarm;
if (urgent || millis() - lastSend >= SEND_EVERY_MS || lastSend == 0) {
LoRa.beginPacket(); LoRa.print(msg); LoRa.endPacket();
lastSend = millis();
Serial.print(F("Sent: ")); Serial.println(msg);
}
delay(200);
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the four SPI wires and that NSS and RST go to the pins in the sketch.
Mount both antennas high and vertical, clear of metal. Range drops sharply behind buildings.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: ESP32-C3 SuperMini Development Board, SX1278 LoRa Module RA-02 433MHz, DHT22 Temperature & Humidity Sensor, 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, TP4056 1A Li-ion Charger Module with Protection, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (lora_mushroom_hut_node.ino). Install these libraries first: LoRa, DHT sensor library and Adafruit Unified Sensor.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,031 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
LoRa radio and spreading factor; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Receiver with an OLED and Receiver with an alarm. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Sent: MUSHR;tempC=26.90;humidity=54.81;ALERT Sent: MUSHR;tempC=27.01;humidity=55.05;ALERT
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.