LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsCheap chargers and worn cables get hot long before they fail. The INA219 sits in the USB lead and reads the current going to the phone. If it stays above 1.8 A the buzzer and red LED warn you. Use it to learn what fast charging really draws, and to check old chargers before trusting them overnight.
Only for low-voltage USB leads. Never connect it to mains or to a charger that you cannot touch safely.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
phone_charger_overcurrent_alarm.inoVerify & upload in Electrolark// Phone charger overcurrent alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "phone-charger-overcurrent-alarm"
#include <Wire.h>
#include <Adafruit_INA219.h>
// ---- pins ----
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_RED = 3;
Adafruit_INA219 ina;
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 1800; // a cheap charger or cable that supplies much more than its rating is heating up
const float HYSTERESIS = 300; // gap that stops rapid on/off switching
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!alertOn && currentMa > ALERT_LEVEL) alertOn = true;
else if (alertOn && currentMa < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "TOO MUCH" : "OK";
}
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
powerMw = ina.getPower_mW();
evaluate();
Serial.print(F("Voltage="));
Serial.print(busV, 2);
Serial.print(F("V"));
Serial.print(F(", Current="));
Serial.print(currentMa, 0);
Serial.print(F("mA"));
Serial.print(F(", Power="));
Serial.print(powerMw, 0);
Serial.print(F("mW"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), INA219 Current and Power Monitor Module, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (phone_charger_overcurrent_alarm.ino). Install this library first: Adafruit INA219.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹576 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Shunt resistors, current and power.
Only for low-voltage USB leads. Never connect it to mains or to a charger that you cannot touch safely.
Ideas that reuse this build: DIY USB power meter and Resettable electronic fuse. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
448mA, Power=5402mW, status=OK Voltage=12.00V, Current=451mA, Power=5403mW, status=OK Voltage=12.02V, Current=448mA, Power=5402mW, status=OK Voltage=12.00V, Current=452mA, Power=5420mW, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.