Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsEarly robot vacuums were not clever: they drove straight, turned a random amount when they met a wall and kept going. This build does the same with one ultrasonic sensor. Randomness is enough to cover most of a room, which makes a nice discussion for a classroom.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Dual H-bridge that lets the board drive two DC motors forwards, backwards and at variable speed.
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + goes to the L298N 12V terminal and battery − to GND; join that GND to the board GND. Power the Uno from the L298N 5 V output or its own USB power bank. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
roomba_style_wander_robot.inoVerify & upload in Electrolark// Roomba-style wandering robot with random turns
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "roomba-style-wander-robot"
// ---- pins ----
const uint8_t ENA = 3;
const uint8_t IN1 = 2;
const uint8_t IN2 = 4;
const uint8_t IN3 = 6;
const uint8_t IN4 = 7;
const uint8_t ENB = 5;
const uint8_t TRIG_PIN = 8;
const uint8_t ECHO_PIN = 12;
// ---- latest readings ----
float distCm = 0;
const float BLOCK_CM = 22;
const int SPEED = 150;
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setup() {
Serial.begin(115200);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
drive(0, 0);
randomSeed(analogRead(A0));
delay(2000);
}
void loop() {
distCm = readDistanceCm();
if (distCm > 0 && distCm < BLOCK_CM) {
drive(-SPEED, -SPEED); delay(300); // back off
int dir = random(2) ? 1 : -1; // pick a side at random
drive(SPEED * dir, -SPEED * dir); delay(random(250, 700));
drive(0, 0); delay(50);
return;
}
drive(SPEED, SPEED);
delay(30);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The ENA/ENB jumpers must be removed and wired to PWM pins, and the battery GND must connect to the board GND.
Swap that motor's two wires on the screw terminal.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, L298N Dual H-Bridge Motor Driver Module, HC-SR04 Ultrasonic Range Finder Sensor Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 2–3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (roomba_style_wander_robot.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,203 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
H-bridges and PWM speed control; Time-of-flight measurement with sound.
Ideas that reuse this build: Obstacle-avoiding robot and Patrol robot car. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.