LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe laser distance sensor looks down at the floor a little ahead of the walker or cane tip. On a flat floor it reads a steady distance; at the edge of a step or an open drain the distance jumps, and the handle vibrates and beeps before the foot goes over. It complements the obstacle-sensing smart cane, which looks forward.
An aid only. It does not see glass, water or very dark surfaces reliably; keep using the cane or walker as normal.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Laser time-of-flight sensor: measures 3 cm to about 1.2 m with millimetre resolution in a tiny package.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
step_and_kerb_drop_detector.inoVerify & upload in Electrolark// Step and kerb drop warning for a cane or walker
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "step-and-kerb-drop-detector"
#include <Wire.h>
#include <Adafruit_VL53L0X.h>
// ---- pins ----
const uint8_t VIBE_PIN = 2;
const uint8_t BUZZER_PIN = 3;
Adafruit_VL53L0X tof;
// ---- latest readings ----
int tofMm = 0;
const unsigned long READ_EVERY_MS = 60;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 450; // pointing at the floor from the walker frame reads about 300 mm; a step down makes it jump
const float HYSTERESIS = 60; // gap that stops rapid on/off switching
int readTofMm() {
VL53L0X_RangingMeasurementData_t m;
tof.rangingTest(&m, false);
return (m.RangeStatus != 4) ? m.RangeMilliMeter : -1;
}
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void evaluate() {
if (!(tofMm > 0)) { statusText = "Sensor error"; return; }
if (!alertOn && tofMm > ALERT_LEVEL) alertOn = true;
else if (alertOn && tofMm < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "DROP" : "OK";
}
void setup() {
Serial.begin(115200);
if (!tof.begin()) Serial.println(F("VL53L0X not found"));
pinMode(VIBE_PIN, OUTPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
tofMm = readTofMm();
evaluate();
Serial.print(F("Range="));
Serial.print(tofMm);
Serial.print(F("mm"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setVibe(alertOn);
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Target is out of range or too dark/shiny. Try a white card within 1 m.
Check the transistor orientation (flat face: C-B-E for BC547).
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
12 parts: Nano CH340 Development Board (Soldered), VL53L0X ToF Laser Distance Sensor Module, Coin Vibration Motor 3V, Active Buzzer Module 3.3–5V, General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, TP4056 1A Li-ion Charger Module with Protection, plus 2 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (step_and_kerb_drop_detector.ino). Install this library first: Adafruit_VL53L0X.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹714 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Laser ranging vs ultrasonic ranging; Transistors as switches.
An aid only. It does not see glass, water or very dark surfaces reliably; keep using the cane or walker as normal.
Ideas that reuse this build: Smart cane and Edge-avoiding robot. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Range=402mm, status=OK Range=398mm, status=OK Range=401mm, status=OK Range=399mm, status=OK Range=399mm, status=OK Range=402mm, status=OK Range=400mm, status=OK Range=401mm, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.