Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA kitchen timer for people who cannot hear a beep or read a small screen. One click of the knob is one minute and the large digits show the time. Press to start; when it reaches zero the vibration motor buzzes in a buzz-buzz-pause pattern for a minute, or until you press the knob. Keep it in a pocket or on the counter.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
vibrating_kitchen_timer.inoVerify & upload in Electrolark// Vibrating kitchen timer with a big knob
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "vibrating-kitchen-timer"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t ENC_CLK = 2;
const uint8_t ENC_DT = 3;
const uint8_t ENC_SW = 4;
const uint8_t SEG_CLK = 5;
const uint8_t SEG_DIO = 6;
const uint8_t VIBE_PIN = 7;
TM1637Display seg(SEG_CLK, SEG_DIO);
int setMin = 5; // minutes chosen with the knob
long leftSec = 0;
bool running = false, ringing = false;
int lastClk = HIGH;
unsigned long lastTick = 0, ringStart = 0;
const unsigned long RING_MS = 60000; // buzz for up to a minute, or until the knob is pressed
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void show(long sec) {
int mm = sec / 60, ss = sec % 60;
seg.showNumberDecEx(mm * 100 + ss, 0b01000000, true); // mm:ss with the colon
}
void setup() {
Serial.begin(115200);
pinMode(ENC_CLK, INPUT_PULLUP);
pinMode(ENC_DT, INPUT_PULLUP);
pinMode(ENC_SW, INPUT_PULLUP);
seg.setBrightness(5);
seg.clear();
pinMode(VIBE_PIN, OUTPUT);
show(setMin * 60L);
}
void loop() {
int clk = digitalRead(ENC_CLK);
if (!running && !ringing && clk != lastClk && clk == LOW) {
setMin = constrain(setMin + ((digitalRead(ENC_DT) != clk) ? 1 : -1), 1, 99);
show(setMin * 60L);
}
lastClk = clk;
if (digitalRead(ENC_SW) == LOW) { // press: start, stop, or silence
if (ringing) { ringing = false; setVibe(false); show(setMin * 60L); }
else if (running) { running = false; show(setMin * 60L); }
else { running = true; leftSec = setMin * 60L; lastTick = millis(); setVibe(true); delay(150); setVibe(false); }
while (digitalRead(ENC_SW) == LOW) delay(10);
}
if (running && millis() - lastTick >= 1000) {
lastTick += 1000; leftSec--; show(leftSec);
if (leftSec <= 0) { running = false; ringing = true; ringStart = millis(); Serial.println(F("Time up")); }
}
if (ringing) {
setVibe((millis() / 400) % 3 != 2); // buzz, buzz, pause pattern you can feel
if (millis() - ringStart > RING_MS) { ringing = false; setVibe(false); show(setMin * 60L); }
}
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn slower, or add 100 nF capacitors from CLK and DT to GND to debounce.
CLK and DIO swapped; swap them.
Check the transistor orientation (flat face: C-B-E for BC547).
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
12 parts: Nano CH340 Development Board (Soldered), KY-040 Incremental Rotary Encoder Module, TM1637 4-Digit 7-Segment Display Module, Coin Vibration Motor 3V, General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, TP4056 1A Li-ion Charger Module with Protection, plus 2 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (vibrating_kitchen_timer.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹676 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Multiplexed 7-segment displays; Quadrature encoders; Transistors as switches.
Ideas that reuse this build: Countdown timer with encoder and Silent vibration doorbell. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.