Component guide · Intermediate · 3 min read
PTC Heaters and Heating Elements
12 V and 24 V Plates, Air Heaters and Safe Use
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A PTC heater is self-regulating: its resistance rises as it warms, so it settles at a set temperature (for example 70, 110 or 220 °C) without a thermostat. They draw a surge of current when cold. Power them from a supply rated for that surge, fuse the circuit, mount them on a heat-resistant surface with airflow, and add a thermostat or controller for precise control.
Key specs at a glance
- Voltage
- 12 V or 24 V DC
- Power
- About 30 W for 35x21x5 mm plates
- Surface temperature
- 70, 110, 120 or 220 °C versions
- Behaviour
- Self-limiting; high current at cold start
- Housing
- Aluminium shell or bare plate
- Uses
- Incubators, dry boxes, enclosures, anti-condensation
How a PTC heater works
PTC means positive temperature coefficient. The element has low resistance when cold, so it heats fast and draws a high current. As it warms, its resistance rises sharply, the current falls and the temperature levels off near the part's rated value. This makes PTC heaters safer than bare resistance wire, but they can still start fires if misused.
Choose the version
Pick by temperature and voltage.
| Version | Surface temperature | Use |
|---|---|---|
| 24 V plate 70 °C | About 70 °C | Gentle warming, dry boxes |
| 24 V plate 110 °C | About 110 °C | Small enclosures, defrosting |
| 24 V plate 220 °C | About 220 °C | High heat: needs care |
| 12 V 30 W air heater (aluminium shell) | About 120 to 220 °C surface | Warm air with a fan |
- 24 V plate 70 °C
- Surface temperature:
- About 70 °C
- Use:
- Gentle warming, dry boxes
- 24 V plate 110 °C
- Surface temperature:
- About 110 °C
- Use:
- Small enclosures, defrosting
- 24 V plate 220 °C
- Surface temperature:
- About 220 °C
- Use:
- High heat: needs care
- 12 V 30 W air heater (aluminium shell)
- Surface temperature:
- About 120 to 220 °C surface
- Use:
- Warm air with a fan
Power and wiring
Plan for the cold-start surge, which can be several times the running current. Use a supply with spare capacity (see power supply sizing), a fuse sized with the fuse tool and thick enough wire; see wire gauge. Switch it with a MOSFET or SSR sized for the surge; see SSR vs relay and MOSFET gate drivers.
Temperature control
Although PTC elements limit themselves, you often need to hold a set air temperature. Add a thermostat or controller with a temperature probe, such as a temperature controller or a PT100 probe. Use heating time to estimate warm-up for a given volume.
Mounting and safety
1. Mount on a heat-resistant surface with a gap for air. 2. Use a fan to move heat, and never cover the heater. 3. Keep it away from plastics and wiring that melt. 4. Add an over-temperature cutout in sealed boxes. 5. Do not leave unattended in new setups. For filament dry boxes see filament storage and for printer chambers see enclosures.
Try it: Heating time calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Using a supply that cannot handle the cold-start surge.
- Skipping a fuse.
- Enclosing the heater without airflow.
- Mounting on plastic that melts.
- Assuming self-limiting means maintenance-free.
Frequently asked questions
What does PTC mean?
Positive temperature coefficient: resistance rises as the element heats.
Do I need a thermostat?
Not to limit the element, but yes to hold an air temperature.
Why does it draw so much current at start?
The cold element has low resistance.
Can I run it from a battery?
Only with a battery and wiring rated for the current.
Is a PTC heater safe for a 3D printer enclosure?
Only with a controller, fuse and over-temperature protection.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






