LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsBatteries lose capacity with age long before their voltage looks bad. Charge the battery fully, connect it, and press the button: the relay connects a load, the INA219 measures the current, and the Uno adds up the mAh until the voltage falls to 10.8 V, where it stops to protect the battery. Compare the result with the rating on the case.
A 12 V battery can deliver hundreds of amps. Put an inline fuse at the battery terminal and insulate every joint before connecting.
Do not leave the test running unattended near anything flammable. Recharge the battery straight after the test.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Two 12 V fans as the test load (add a 12 V bulb for a faster test)
Follow the colours: red is power, dark grey is ground, blue is a signal.
battery_capacity_tester_12v.inoVerify & upload in Electrolark// 12 V battery capacity tester
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "battery-capacity-tester-12v"
#include <Wire.h>
#include <Adafruit_INA219.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t RELAY_PIN = 2;
const uint8_t BUTTON_PIN = 3;
Adafruit_INA219 ina;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const float CUTOFF_V = 10.8; // stop here to protect the battery
double mah = 0, wh = 0;
bool testing = false, done = false;
unsigned long lastMs = 0, lastShow = 0, startMs = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lcd.init();
lcd.backlight();
pinMode(BUTTON_PIN, INPUT_PULLUP);
setRelay(false);
}
void loop() {
unsigned long now = millis();
if (!testing && digitalRead(BUTTON_PIN) == LOW) { testing = true; done = false; mah = 0; wh = 0; startMs = lastMs = now; setRelay(true); delay(300); }
if (now - lastMs < 1000) return;
float hours = (now - lastMs) / 3600000.0f; lastMs = now;
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
if (testing) {
mah += currentMa * hours; wh += busV * currentMa / 1000.0 * hours;
if (busV < CUTOFF_V) { testing = false; done = true; setRelay(false); Serial.println(F("Test finished")); }
}
char a[8], buf[17];
dtostrf(busV, 5, 2, a);
snprintf(buf, sizeof(buf), "%sV %4dmA ", a, (int)currentMa);
lcd.setCursor(0, 0); lcd.print(buf);
snprintf(buf, sizeof(buf), "%s%6dmAh ", testing ? "Run " : done ? "Done" : "Idle", (int)mah);
lcd.setCursor(0, 1); lcd.print(buf);
Serial.print((now - startMs) / 60000); Serial.print(F(" min, ")); Serial.print(busV, 2); Serial.print(F(" V, ")); Serial.print(mah, 0); Serial.println(F(" mAh"));
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, INA219 Current and Power Monitor Module, 5V Relay Module with Optocoupler (1 channel), LCD1602 16x2 Character LCD (blue, with I2C adapter), Tactile Push Button Switch, 2 × 12V DC Brushless Fan 80mm (cooling fan), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 2 hours plus test time. The build on this page has 10 steps.
No. This page has the complete, tested code (battery_capacity_tester_12v.ino). Install these libraries first: Adafruit INA219 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,139 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Isolation, relays and switching higher-power loads; Pull-ups and debouncing; Shunt resistors, current and power.
Ideas that reuse this build: Runtime estimator and Battery discharge in class. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0 min, 11.98 V, 0 mAh 0 min, 12.00 V, 0 mAh
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.