LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsTwo lamps may give the same light but draw very different power. The INA219 sits in series with each lamp on a 12 V adapter and shows volts, milliamps and milliwatts. Students find the LED uses a fraction of the power and see why it saves money on the electricity bill.
Use only 12 V lamps and a 12 V adapter. Never connect mains lamps to this circuit.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Wire VIN+ to the adapter +, VIN− to the lamp, and the lamp back to the adapter −. Power the Nano from USB. Bring your own 12 V LED lamp and filament bulb.
class_led_vs_bulb_power.inoVerify & upload in Electrolark// LED bulb or filament bulb: who uses more power?
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-led-vs-bulb-power"
#include <Wire.h>
#include <Adafruit_INA219.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_INA219 ina;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Lamp power"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Voltage: "));
oled.print(busV, 2);
oled.print(F(" V"));
oled.setCursor(0, 24);
oled.print(F("Current: "));
oled.print(currentMa, 0);
oled.print(F(" mA"));
oled.setCursor(0, 34);
oled.print(F("Power: "));
oled.print(powerMw, 0);
oled.print(F(" mW"));
oled.display();
}
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
powerMw = ina.getPower_mW();
Serial.print(F("Voltage="));
Serial.print(busV, 2);
Serial.print(F("V"));
Serial.print(F(", Current="));
Serial.print(currentMa, 0);
Serial.print(F("mA"));
Serial.print(F(", Power="));
Serial.print(powerMw, 0);
Serial.print(F("mW"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 12 V adapter and 12 V lamps under 1 A, never mains. Compare brightness by eye or with the light sensor, then compare the power.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), INA219 Current and Power Monitor Module, 0.96" OLED Display 128x64 (I2C), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_led_vs_bulb_power.ino). Install these libraries first: Adafruit INA219, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹867 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Electric power; Energy saving.
Use only 12 V lamps and a 12 V adapter. Never connect mains lamps to this circuit.
Ideas that reuse this build: Ohm's law lab and Motor load current. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Voltage=12.02V, Current=448mA, Power=5402mW Voltage=12.00V, Current=451mA, Power=5403mW Voltage=12.02V, Current=448mA, Power=5402mW Voltage=12.00V, Current=452mA, Power=5420mW
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.