Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsA free-spinning motor draws little current. Pinch the shaft and it slows, the current rises and so does the power taken from the battery. The INA219 shows both. Students learn why stalled motors get hot and why robots need a strong battery.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures voltage, current and power of a DC circuit up to 26 V and 3.2 A through a tiny shunt resistor, and reports them over I²C.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + goes to VIN+, VIN− goes to the motor, and the motor's other lead goes to battery −. Join battery − to the board GND.
class_motor_load_current.inoVerify & upload in Electrolark// How hard is the motor working?
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-motor-load-current"
#include <Wire.h>
#include <Adafruit_INA219.h>
#include <LiquidCrystal_I2C.h>
Adafruit_INA219 ina;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float busV = 0;
float currentMa = 0;
float powerMw = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Current "));
lcd.print(currentMa, 0);
lcd.print(F(" mA"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Power "));
lcd.print(powerMw, 0);
lcd.print(F(" mW"));
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
if (!ina.begin()) Serial.println(F("INA219 not found"));
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
busV = ina.getBusVoltage_V();
currentMa = ina.getCurrent_mA();
powerMw = ina.getPower_mW();
Serial.print(F("Current="));
Serial.print(currentMa, 0);
Serial.print(F("mA"));
Serial.print(F(", Power="));
Serial.print(powerMw, 0);
Serial.print(F("mW"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x40.
The + wire must pass through VIN+ to VIN−; measuring on the GND side does not work.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a TT or BO motor on 4 AA cells. Record current spinning freely, lightly held and nearly stalled. Do not hold a stalled motor for more than a few seconds.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, INA219 Current and Power Monitor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), BO DC Gear Motor 3–12V, Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 30 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_motor_load_current.ino). Install these libraries first: Adafruit INA219 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹762 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Motors and load; Electrical power.
Ideas that reuse this build: Motor stall current cut-off and DC current meter. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
mA, Power=5387mW Current=451mA, Power=5373mW Current=449mA, Power=5424mW Current=451mA, Power=5388mW Current=450mA, Power=5411mW Current=449mA, Power=5421mW
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.