Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsEvery home has a spare infrared remote. The receiver on the car reads the button codes, and the Uno drives forward, back, left or right while you hold a key. Holding a key sends repeat codes; when they stop arriving the car stops, so it never runs away. Learn your remote's codes from the Serial Monitor and put them in the sketch.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Dual H-bridge that lets the board drive two DC motors forwards, backwards and at variable speed.
38 kHz infrared receiver that decodes button codes from almost any TV or AC remote.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + goes to the L298N 12V terminal and battery − to GND; join that GND to the board GND. Power the Uno from the L298N 5 V output or its own USB power bank. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
ir_remote_controlled_car.inoVerify & upload in Electrolark// TV-remote controlled robot car
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "ir-remote-controlled-car"
#include <IRremote.hpp>
// ---- pins ----
const uint8_t ENA = 3;
const uint8_t IN1 = 2;
const uint8_t IN2 = 4;
const uint8_t IN3 = 6;
const uint8_t IN4 = 7;
const uint8_t ENB = 5;
const uint8_t IR_PIN = 8;
// Press remote buttons with the Serial Monitor open, then put their command numbers here
const uint16_t CMD_FWD = 0x18, CMD_BACK = 0x52, CMD_LEFT = 0x08, CMD_RIGHT = 0x5A, CMD_STOP = 0x1C;
const int SPEED = 190, TURN = 150;
const unsigned long FAILSAFE_MS = 400; // stop when the button is let go (repeats stop arriving)
unsigned long lastCmd = 0;
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
void setup() {
Serial.begin(115200);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
IrReceiver.begin(IR_PIN);
drive(0, 0);
}
void loop() {
if (IrReceiver.decode()) {
uint16_t cmd = IrReceiver.decodedIRData.command;
IrReceiver.resume();
lastCmd = millis();
if (cmd == CMD_FWD) drive(SPEED, SPEED);
else if (cmd == CMD_BACK) drive(-SPEED, -SPEED);
else if (cmd == CMD_LEFT) drive(-TURN, TURN);
else if (cmd == CMD_RIGHT) drive(TURN, -TURN);
else if (cmd == CMD_STOP) drive(0, 0);
else { Serial.print(F("Unused command 0x")); Serial.println(cmd, HEX); }
}
if (millis() - lastCmd > FAILSAFE_MS) drive(0, 0); // holding a button sends repeats; letting go stops the car
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The ENA/ENB jumpers must be removed and wired to PWM pins, and the battery GND must connect to the board GND.
Swap that motor's two wires on the screw terminal.
Point the remote straight at the receiver, check the OUT pin, and try a fresh remote battery.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, L298N Dual H-Bridge Motor Driver Module, Digital 38kHz Infrared Receiver Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (ir_remote_controlled_car.ino). Install this library first: IRremote.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,175 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
H-bridges and PWM speed control; Infrared remote protocols (NEC).
Ideas that reuse this build: Bluetooth RC car and IR remote relay switch. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.